[PATCH v3 1/5] pinctrl/lantiq: updating devicetree binding description

@@ -1,7 +1,16 @@
 Lantiq XWAY pinmux controller
 
 Required properties:
-- compatible: "lantiq,pinctrl-xway" or "lantiq,pinctrl-xr9"
+- compatible: "lantiq,pinctrl-xway", (DEPRECATED: Use "lantiq,pinctrl-danube")
+	      "lantiq,pinctrl-xr9", (DEPRECATED: Use "lantiq,xrx100-pinctrl" or
+					"lantiq,xrx200-pinctrl")
+	      "lantiq,pinctrl-ase", (DEPRECATED: Use "lantiq,ase-pinctrl")
+	      "lantiq,<chip>-pinctrl", where <chip> is:
+		"ase" (XWAY AMAZON Family)
+		"danube" (XWAY DANUBE Family)
+		"xrx100" (XWAY xRX100 Family)
+		"xrx200" (XWAY xRX200 Family)
+		"xrx300" (XWAY xRX300 Family)
 - reg: Should contain the physical address and length of the gpio/pinmux
   register range
 

@@ -36,19 +45,87 @@ Required subnode-properties:
 
 Valid values for group and function names:
 
+XWAY: (DEPRECATED: Use DANUBE)
   mux groups:
     exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1,
     ebu wait, nand ale, nand cs1, nand cle, spi, spi_cs1, spi_cs2, spi_cs3,
-    spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi , gpt1, gpt2,
+    spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi, gpt1, gpt2,
     gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3, req1, req2,
     req3
 
-  additional mux groups (XR9 only):
-    mdio, nand rdy, nand rd, exin3, exin4, gnt4, req4
+  functions:
+    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu
+
+XR9: ( DEPRECATED: Use xRX100/xRX200)
+  mux groups:
+    exin0, exin1, exin2, exin3, exin4, jtag, ebu a23, ebu a24, ebu a25,
+    ebu clk, ebu cs1, ebu wait, nand ale, nand cs1, nand cle, nand rdy,
+    nand rd, spi, spi_cs1, spi_cs2, spi_cs3, spi_cs4, spi_cs5, spi_cs6,
+    asc0, asc0 cts rts, stp, nmi, gpt1, gpt2, gpt3, clkout0, clkout1,
+    clkout2, clkout3, gnt1, gnt2, gnt3, gnt4, req1, req2, req3, req4, mdio,
+    gphy0 led0, gphy0 led1, gphy0 led2, gphy1 led0, gphy1 led1, gphy1 led2
+
+  functions:
+    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio, gphy
+
+AMAZON:
+  mux groups:
+    exin0, exin1, exin2, jtag, spi_di, spi_do, spi_clk, spi_cs1, spi_cs2,
+    spi_cs3, spi_cs4, spi_cs5, spi_cs6, asc, stp, gpt1, gpt2, gpt3, clkout0,
+    clkout1, clkout2, mdio, dfe led0, dfe led1, ephy led0, ephy led1, ephy led2
+
+  functions:
+    spi, asc, cgu, jtag, exin, stp, gpt, mdio, ephy, dfe
+
+DANUBE:
+  mux groups:
+    exin0, exin1, exin2, jtag, ebu a23, ebu a24, ebu a25, ebu clk, ebu cs1,
+    ebu wait, nand ale, nand cs1, nand cle, spi_di, spi_do, spi_clk, spi_cs1,
+    spi_cs2, spi_cs3, spi_cs4, spi_cs5, spi_cs6, asc0, asc0 cts rts, stp, nmi,
+    gpt1, gpt2, gpt3, clkout0, clkout1, clkout2, clkout3, gnt1, gnt2, gnt3,
+    req1, req2, req3, dfe led0, dfe led1
 
   functions:
-    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, mdio
+    spi, asc, cgu, jtag, exin, stp, gpt, nmi, pci, ebu, dfe
 
+xRX100:
+  mux groups:
+    exin0, exin1, exin2, exin3, exin4, ebu a23, ebu a24, ebu a25, ebu clk,
+    ebu cs1, ebu wait, nand ale, nand cs1, nand cle, nand rdy, nand rd,
+    spi_di, spi_do, spi_clk, spi_cs1, spi_cs2, spi_cs3, spi_cs4, spi_cs5,
+    spi_cs6, asc0, asc0 cts rts, stp, nmi, gpt1, gpt2, gpt3, clkout0, clkout1,
+    clkout2, clkout3, gnt1, gnt2, gnt3, gnt4, req1, req2, req3, req4, mdio,
+    dfe led0, dfe led1
+
+  functions:
+    spi, asc, cgu, exin, stp, gpt, nmi, pci, ebu, mdio, dfe
+
+xRX200:
+  mux groups:
+    exin0, exin1, exin2, exin3, exin4, ebu a23, ebu a24, ebu a25, ebu clk,
+    ebu cs1, ebu wait, nand ale, nand cs1, nand cle, nand rdy, nand rd,
+    spi_di, spi_do, spi_clk, spi_cs1, spi_cs2, spi_cs3, spi_cs4, spi_cs5,
+    spi_cs6, usif uart_rx, usif uart_tx, usif uart_rts, usif uart_cts,
+    usif uart_dtr, usif uart_dsr, usif uart_dcd, usif uart_ri, usif spi_di,
+    usif spi_do, usif spi_clk, usif spi_cs0, usif spi_cs1, usif spi_cs2,
+    stp, nmi, gpt1, gpt2, gpt3, clkout0, clkout1, clkout2, clkout3, gnt1,
+    gnt2, gnt3, gnt4, req1, req2, req3, req4, mdio, dfe led0, dfe led1,
+    gphy0 led0, gphy0 led1, gphy0 led2, gphy1 led0, gphy1 led1, gphy1 led2
+
+  functions:
+    spi, usif, cgu, exin, stp, gpt, nmi, pci, ebu, mdio, dfe, gphy
+
+xRX300:
+  mux groups:
+    exin0, exin1, exin2, exin4, nand ale, nand cs0, nand cs1, nand cle,
+    nand rdy, nand rd, nand_d0, nand_d1, nand_d2, nand_d3, nand_d4, nand_d5,
+    nand_d6, nand_d7, nand_d1, nand wr, nand wp, nand se, spi_di, spi_do,
+    spi_clk, spi_cs1, spi_cs4, spi_cs6, usif uart_rx, usif uart_tx,
+    usif spi_di, usif spi_do, usif spi_clk, usif spi_cs0, stp, clkout2,
+    mdio, dfe led0, dfe led1, ephy0 led0, ephy0 led1, ephy1 led0, ephy1 led1
+
+  functions:
+    spi, usif, cgu, exin, stp, ebu, mdio, dfe, ephy
 
 
 Definition of pin configurations:

@@ -62,15 +139,32 @@ Optional subnode-properties:
     0: none, 1: down, 2: up.
 - lantiq,open-drain: Boolean, enables open-drain on the defined pin.
 
-Valid values for XWAY pin names:
+Valid values for XWAY pin names: (DEPRECATED: Use DANUBE)
   Pinconf pins can be referenced via the names io0-io31.
 
-Valid values for XR9 pin names:
+Valid values for XR9 pin names: (DEPRECATED: Use xrX100/xRX200)
   Pinconf pins can be referenced via the names io0-io55.
 
+Valid values for AMAZON pin names:
+  Pinconf pins can be referenced via the names io0-io31.
+
+Valid values for DANUBE pin names:
+  Pinconf pins can be referenced via the names io0-io31.
+
+Valid values for xRX100 pin names:
+  Pinconf pins can be referenced via the names io0-io55.
+
+Valid values for xRX200 pin names:
+  Pinconf pins can be referenced via the names io0-io49.
+
+Valid values for xRX300 pin names:
+  Pinconf pins can be referenced via the names io0-io1,io3-io6,io8-io11,
+						io13-io19,io23-io27,io34-io36,
+						io42-io43,io48-io61.
+
 Example:
 	gpio: pinmux@E100B10 {
-		compatible = "lantiq,pinctrl-xway";
+		compatible = "lantiq,danube-pinctrl";
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 

@@ -52,7 +52,7 @@
 		};
 
 		gpio: pinmux@E100B10 {
-			compatible = "lantiq,pinctrl-xway";
+			compatible = "lantiq,danube-pinctrl";
 			pinctrl-names = "default";
 			pinctrl-0 = <&state_default>;
 

@@ -1563,6 +1563,10 @@ static int xway_gpio_dir_out(struct gpio_chip *chip, unsigned int pin, int val)
 {
 	struct ltq_pinmux_info *info = dev_get_drvdata(chip->dev);
 
+	if (PORT(pin) == PORT3)
+		gpio_setbit(info->membase[0], GPIO3_OD, PORT_PIN(pin));
+	else
+		gpio_setbit(info->membase[0], GPIO_OD(pin), PORT_PIN(pin));
 	gpio_setbit(info->membase[0], GPIO_DIR(pin), PORT_PIN(pin));
 	xway_gpio_set(chip, pin, val);
 

@@ -1573,6 +1573,18 @@ static int xway_gpio_dir_out(struct gpio_chip *chip, unsigned int pin, int val)
 	return 0;
 }
 
+static int xway_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	struct ltq_pinmux_info *info = dev_get_drvdata(chip->dev);
+	int i;
+
+	for (i = 0; i < info->num_exin; i++)
+		if (info->exin[i] == offset)
+			return ltq_eiu_get_irq(i);
+
+	return -1;
+}
+
 static struct gpio_chip xway_chip = {
 	.label = "gpio-xway",
 	.direction_input = xway_gpio_dir_in,

@@ -1581,6 +1593,7 @@ static struct gpio_chip xway_chip = {
 	.set = xway_gpio_set,
 	.request = gpiochip_generic_request,
 	.free = gpiochip_generic_free,
+	.to_irq = xway_gpio_to_irq,
 	.base = -1,
 };