[PATCH] media: dt-bindings: Use consistent indentation in the example

From: Krzysztof Kozlowski <hidden>
Date: 2026-09-13 12:33:10
Also in: linux-arm-msm, linux-devicetree, linux-media, lkml
Subsystem: arm mali-c55 isp driver, arm/qualcomm mailing list, broadcom bcm2835 camera drivers, cadence mipi-csi2 bridges, imgtec jpeg encoder driver, media drivers for stm32 - dcmi / dcmipp, media input infrastructure (v4l/dvb), microchip csi2dc driver, microchip isc driver, omnivision ov2680 sensor driver, omnivision ov2732 sensor driver, open firmware and flattened device tree bindings, qualcomm camera subsystem driver, qualcomm media platform, raspberry pi pisp back end, samsung s5p/exynos4 soc series camera subsystem drivers, the rest, ti vpe/cal drivers · Maintainers: Daniel Scally, Jacopo Mondi, Raspberry Pi Kernel Maintenance, Maxime Ripard, Devarsh Thakkar, Hugues Fruchet, Alain Volmat, Mauro Carvalho Chehab, Eugen Hristev, Rui Miguel Silva, Hans de Goede, Walter Werner Schneider, Rob Herring, Krzysztof Kozlowski, Conor Dooley, Bryan O'Donoghue, Bryan O'Donoghue, Sylwester Nawrocki, Linus Torvalds, Yemike Abhilash Chandra

Correct indentation in the examples to consistent 2- or 4-spaces
indentation to fix dt-check-style warnings ("example 0
[indent-consistent] indent mismatch ...").  Preferred is 4-spaces, but
re-indenting entire example just for that is too much churn.

Signed-off-by: Krzysztof Kozlowski <redacted>
---
 .../bindings/media/arm,mali-c55.yaml          |  2 +-
 .../devicetree/bindings/media/atmel,isc.yaml  | 14 ++---
 .../bindings/media/brcm,bcm2835-unicam.yaml   | 10 ++--
 .../bindings/media/cdns,csi2rx.yaml           | 58 +++++++++----------
 .../bindings/media/i2c/ovti,ov2680.yaml       | 26 ++++-----
 .../bindings/media/i2c/ovti,ov2732.yaml       |  6 +-
 .../bindings/media/img,e5010-jpeg-enc.yaml    | 22 +++----
 .../bindings/media/microchip,csi2dc.yaml      | 52 ++++++++---------
 .../bindings/media/microchip,xisc.yaml        | 14 ++---
 .../bindings/media/qcom,x1e80100-camss.yaml   | 26 ++++-----
 .../bindings/media/raspberrypi,pispbe.yaml    | 10 ++--
 .../bindings/media/samsung,fimc.yaml          | 14 ++---
 .../bindings/media/st,stm32-dcmi.yaml         | 16 ++---
 .../bindings/media/st,stm32-dcmipp.yaml       | 14 ++---
 .../devicetree/bindings/media/ti,cal.yaml     | 48 +++++++--------
 15 files changed, 166 insertions(+), 166 deletions(-)

diff --git a/Documentation/devicetree/bindings/media/arm,mali-c55.yaml b/Documentation/devicetree/bindings/media/arm,mali-c55.yaml
index fc4fcd19922a..39af7ffc70b4 100644
--- a/Documentation/devicetree/bindings/media/arm,mali-c55.yaml
+++ b/Documentation/devicetree/bindings/media/arm,mali-c55.yaml

@@ -79,7 +79,7 @@ examples:
 
       port {
         isp_in: endpoint {
-            remote-endpoint = <&csi2_rx_out>;
+          remote-endpoint = <&csi2_rx_out>;
         };
       };
     };

diff --git a/Documentation/devicetree/bindings/media/atmel,isc.yaml b/Documentation/devicetree/bindings/media/atmel,isc.yaml
index dc8aba698d78..5c84f372e81a 100644
--- a/Documentation/devicetree/bindings/media/atmel,isc.yaml
+++ b/Documentation/devicetree/bindings/media/atmel,isc.yaml

@@ -102,12 +102,12 @@ examples:
         clock-output-names = "isc-mck";
 
         port {
-                isc_0: endpoint {
-                       remote-endpoint = <&ov7740_0>;
-                       hsync-active = <1>;
-                       vsync-active = <0>;
-                       pclk-sample = <1>;
-                       bus-width = <8>;
-                };
+            isc_0: endpoint {
+                remote-endpoint = <&ov7740_0>;
+                hsync-active = <1>;
+                vsync-active = <0>;
+                pclk-sample = <1>;
+                bus-width = <8>;
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml b/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
index 5fb5d60f069a..bfec4daccd0a 100644
--- a/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml
+++ b/Documentation/devicetree/bindings/media/brcm,bcm2835-unicam.yaml

@@ -117,11 +117,11 @@ examples:
         power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>;
         brcm,num-data-lanes = <2>;
         port {
-                csi1_ep: endpoint {
-                        remote-endpoint = <&imx219_0>;
-                        bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
-                        data-lanes = <1 2>;
-                };
+            csi1_ep: endpoint {
+                remote-endpoint = <&imx219_0>;
+                bus-type = <MEDIA_BUS_TYPE_CSI2_DPHY>;
+                data-lanes = <1 2>;
+            };
         };
     };
 ...

diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml b/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml
index 6ed9a5621064..cbc6249e8803 100644
--- a/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml
+++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.yaml

@@ -160,50 +160,50 @@ examples:
         phy-names = "dphy";
 
         ports {
-                #address-cells = <1>;
-                #size-cells = <0>;
+            #address-cells = <1>;
+            #size-cells = <0>;
 
-                port@0 {
-                    reg = <0>;
+            port@0 {
+                reg = <0>;
 
-                    csi2rx_in_sensor: endpoint {
-                        remote-endpoint = <&sensor_out_csi2rx>;
-                        clock-lanes = <0>;
-                        data-lanes = <1 2>;
-                    };
+                csi2rx_in_sensor: endpoint {
+                    remote-endpoint = <&sensor_out_csi2rx>;
+                    clock-lanes = <0>;
+                    data-lanes = <1 2>;
                 };
+            };
 
-                port@1 {
-                    reg = <1>;
+            port@1 {
+                reg = <1>;
 
-                    csi2rx_out_grabber0: endpoint {
-                        remote-endpoint = <&grabber0_in_csi2rx>;
-                    };
+                csi2rx_out_grabber0: endpoint {
+                    remote-endpoint = <&grabber0_in_csi2rx>;
                 };
+            };
 
-                port@2 {
-                    reg = <2>;
+            port@2 {
+                reg = <2>;
 
-                    csi2rx_out_grabber1: endpoint {
-                        remote-endpoint = <&grabber1_in_csi2rx>;
-                    };
+                csi2rx_out_grabber1: endpoint {
+                    remote-endpoint = <&grabber1_in_csi2rx>;
                 };
+            };
 
-                port@3 {
-                    reg = <3>;
+            port@3 {
+                reg = <3>;
 
-                    csi2rx_out_grabber2: endpoint {
-                        remote-endpoint = <&grabber2_in_csi2rx>;
-                    };
+                csi2rx_out_grabber2: endpoint {
+                    remote-endpoint = <&grabber2_in_csi2rx>;
                 };
+            };
 
-                port@4 {
-                    reg = <4>;
+            port@4 {
+                reg = <4>;
 
-                    csi2rx_out_grabber3: endpoint {
-                        remote-endpoint = <&grabber3_in_csi2rx>;
-                    };
+                csi2rx_out_grabber3: endpoint {
+                    remote-endpoint = <&grabber3_in_csi2rx>;
                 };
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
index 634d3b821b8c..83f84a7828bf 100644
--- a/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2680.yaml

@@ -90,22 +90,22 @@ examples:
         #size-cells = <0>;
 
         ov2680: camera-sensor@36 {
-                compatible = "ovti,ov2680";
-                reg = <0x36>;
-                clocks = <&osc>;
-                clock-names = "xvclk";
-                reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+            compatible = "ovti,ov2680";
+            reg = <0x36>;
+            clocks = <&osc>;
+            clock-names = "xvclk";
+            reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
-                DOVDD-supply = <&sw2_reg>;
-                DVDD-supply = <&sw2_reg>;
-                AVDD-supply = <&reg_peri_3p15v>;
+            DOVDD-supply = <&sw2_reg>;
+            DVDD-supply = <&sw2_reg>;
+            AVDD-supply = <&reg_peri_3p15v>;
 
-                port {
-                        ov2680_to_mipi: endpoint {
-                                remote-endpoint = <&mipi_from_sensor>;
-                                link-frequencies = /bits/ 64 <330000000>;
-                        };
+            port {
+                ov2680_to_mipi: endpoint {
+                    remote-endpoint = <&mipi_from_sensor>;
+                    link-frequencies = /bits/ 64 <330000000>;
                 };
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml
index 814fc568c550..b6b5145802e7 100644
--- a/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml
+++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov2732.yaml

@@ -94,9 +94,9 @@ examples:
 
             port {
                 camera_out: endpoint {
-                  data-lanes = <1 2>;
-                  link-frequencies = /bits/ 64 <360000000>;
-                  remote-endpoint = <&mipi_in_camera>;
+                    data-lanes = <1 2>;
+                    link-frequencies = /bits/ 64 <360000000>;
+                    remote-endpoint = <&mipi_in_camera>;
                 };
             };
         };

diff --git a/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml b/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml
index 085020cb9e61..b6f80098beb7 100644
--- a/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml
+++ b/Documentation/devicetree/bindings/media/img,e5010-jpeg-enc.yaml

@@ -61,15 +61,15 @@ examples:
     #include <dt-bindings/interrupt-controller/irq.h>
 
     soc {
-      #address-cells = <2>;
-      #size-cells = <2>;
-      jpeg-encoder@fd20000 {
-          compatible = "img,e5010-jpeg-enc";
-          reg = <0x00 0xfd20000 0x00 0x100>,
-                <0x00 0xfd20200 0x00 0x200>;
-          reg-names = "core", "mmu";
-          clocks = <&k3_clks 201 0>;
-          power-domains = <&k3_pds 201 TI_SCI_PD_EXCLUSIVE>;
-          interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-      };
+        #address-cells = <2>;
+        #size-cells = <2>;
+        jpeg-encoder@fd20000 {
+            compatible = "img,e5010-jpeg-enc";
+            reg = <0x00 0xfd20000 0x00 0x100>,
+                  <0x00 0xfd20200 0x00 0x200>;
+            reg-names = "core", "mmu";
+            clocks = <&k3_clks 201 0>;
+            power-domains = <&k3_pds 201 TI_SCI_PD_EXCLUSIVE>;
+            interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+        };
     };

diff --git a/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml b/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml
index b3a345fc6464..d06987680ed8 100644
--- a/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml
+++ b/Documentation/devicetree/bindings/media/microchip,csi2dc.yaml

@@ -149,22 +149,22 @@ examples:
         clock-names = "pclk", "scck";
 
         ports {
-               #address-cells = <1>;
-               #size-cells = <0>;
-               port@0 {
-                       reg = <0>; /* must be 0, first child port */
-                       csi2dc_in: endpoint { /* input from IDI interface */
-                               bus-type = <4>; /* MIPI CSI2 D-PHY */
-                               remote-endpoint = <&csi2host_out>;
-                       };
-               };
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@0 {
+                reg = <0>; /* must be 0, first child port */
+                csi2dc_in: endpoint { /* input from IDI interface */
+                    bus-type = <4>; /* MIPI CSI2 D-PHY */
+                    remote-endpoint = <&csi2host_out>;
+                };
+            };
 
-               port@1 {
-                       reg = <1>; /* must be 1, second child port */
-                       csi2dc_out: endpoint {
-                               remote-endpoint = <&xisc_in>; /* output to sensor controller */
-                       };
-               };
+            port@1 {
+                reg = <1>; /* must be 1, second child port */
+                csi2dc_out: endpoint {
+                    remote-endpoint = <&xisc_in>; /* output to sensor controller */
+                };
+            };
         };
     };

@@ -181,18 +181,18 @@ examples:
         dma-names = "rx";
 
         ports {
-               #address-cells = <1>;
-               #size-cells = <0>;
-               port@0 {
-                       reg = <0>; /* must be 0, first child port */
-                       csi2dc_input: endpoint { /* input from IDI interface */
-                               remote-endpoint = <&csi2host_out>;
-                       };
-               };
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@0 {
+                reg = <0>; /* must be 0, first child port */
+                csi2dc_input: endpoint { /* input from IDI interface */
+                    remote-endpoint = <&csi2host_out>;
+                };
+            };
 
-               port@1 {
-                       reg = <1>;
-               };
+            port@1 {
+                reg = <1>;
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/microchip,xisc.yaml b/Documentation/devicetree/bindings/media/microchip,xisc.yaml
index 25f5f79d40ce..6a9e56c486c2 100644
--- a/Documentation/devicetree/bindings/media/microchip,xisc.yaml
+++ b/Documentation/devicetree/bindings/media/microchip,xisc.yaml

@@ -118,12 +118,12 @@ examples:
         clock-output-names = "isc-mck";
 
         port {
-                xisc_in: endpoint {
-                       bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
-                       remote-endpoint = <&csi2dc_out>;
-                       hsync-active = <1>;
-                       vsync-active = <1>;
-                       bus-width = <12>;
-                };
+            xisc_in: endpoint {
+                bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
+                remote-endpoint = <&csi2dc_out>;
+                hsync-active = <1>;
+                vsync-active = <1>;
+                bus-width = <12>;
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml b/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml
index 2d1662ef522b..bdf03a944fd7 100644
--- a/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml
+++ b/Documentation/devicetree/bindings/media/qcom,x1e80100-camss.yaml

@@ -289,19 +289,19 @@ examples:
                           "vfe_lite_cphy_rx",
                           "vfe_lite_csid";
 
-           interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>,
-                        <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>;
+            interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 466 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 431 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 468 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 359 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 477 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 478 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 479 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 467 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 469 IRQ_TYPE_EDGE_RISING>,
+                         <GIC_SPI 360 IRQ_TYPE_EDGE_RISING>;
 
             interrupt-names = "csid0",
                               "csid1",

diff --git a/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml b/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml
index 5c0f2f7b1d95..36fde927382a 100644
--- a/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml
+++ b/Documentation/devicetree/bindings/media/raspberrypi,pispbe.yaml

@@ -54,10 +54,10 @@ examples:
         #size-cells = <2>;
 
         isp@880000 {
-             compatible = "brcm,bcm2712-pispbe", "raspberrypi,pispbe";
-             reg = <0x10 0x00880000 0x0 0x4000>;
-             interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-             clocks = <&firmware_clocks 7>;
-             iommus = <&iommu2>;
+            compatible = "brcm,bcm2712-pispbe", "raspberrypi,pispbe";
+            reg = <0x10 0x00880000 0x0 0x4000>;
+            interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&firmware_clocks 7>;
+            iommus = <&iommu2>;
         };
     };

diff --git a/Documentation/devicetree/bindings/media/samsung,fimc.yaml b/Documentation/devicetree/bindings/media/samsung,fimc.yaml
index 1bfba84f8854..1329d4ee0705 100644
--- a/Documentation/devicetree/bindings/media/samsung,fimc.yaml
+++ b/Documentation/devicetree/bindings/media/samsung,fimc.yaml

@@ -188,13 +188,13 @@ examples:
         /* ... CSIS 1 */
 
         fimc-lite@b90000 {
-              compatible = "samsung,exynos4212-fimc-lite";
-              reg = <0xb90000 0x1000>;
-              interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
-              power-domains = <&pd_isp>;
-              clocks = <&isp_clock CLK_ISP_FIMC_LITE0>;
-              clock-names = "flite";
-              iommus = <&sysmmu_fimc_lite0>;
+            compatible = "samsung,exynos4212-fimc-lite";
+            reg = <0xb90000 0x1000>;
+            interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+            power-domains = <&pd_isp>;
+            clocks = <&isp_clock CLK_ISP_FIMC_LITE0>;
+            clock-names = "flite";
+            iommus = <&sysmmu_fimc_lite0>;
         };
 
         /* ... FIMC-LITE 1 */

diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
index 7c2ddd27780f..cb0116176c3f 100644
--- a/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml
+++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.yaml

@@ -120,14 +120,14 @@ examples:
         dma-names = "tx";
 
         port {
-             dcmi_0: endpoint {
-                   remote-endpoint = <&ov5640_0>;
-                   bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
-                   bus-width = <8>;
-                   hsync-active = <0>;
-                   vsync-active = <0>;
-                   pclk-sample = <1>;
-             };
+            dcmi_0: endpoint {
+                remote-endpoint = <&ov5640_0>;
+                bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
+                bus-width = <8>;
+                hsync-active = <0>;
+                vsync-active = <0>;
+                pclk-sample = <1>;
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml b/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml
index 162a0c526d5d..0bf7c674dd97 100644
--- a/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml
+++ b/Documentation/devicetree/bindings/media/st,stm32-dcmipp.yaml

@@ -120,13 +120,13 @@ examples:
         clocks = <&rcc DCMIPP_K>;
 
         port {
-             endpoint {
-                   remote-endpoint = <&mipid02_2>;
-                   bus-width = <8>;
-                   hsync-active = <0>;
-                   vsync-active = <0>;
-                   pclk-sample = <0>;
-             };
+            endpoint {
+                remote-endpoint = <&mipid02_2>;
+                bus-width = <8>;
+                hsync-active = <0>;
+                vsync-active = <0>;
+                pclk-sample = <0>;
+            };
         };
     };

diff --git a/Documentation/devicetree/bindings/media/ti,cal.yaml b/Documentation/devicetree/bindings/media/ti,cal.yaml
index f1a940a110d2..c223b4f2d75a 100644
--- a/Documentation/devicetree/bindings/media/ti,cal.yaml
+++ b/Documentation/devicetree/bindings/media/ti,cal.yaml

@@ -136,17 +136,17 @@ examples:
         ti,camerrx-control = <&scm_conf 0xE94>;
 
         ports {
-              #address-cells = <1>;
-              #size-cells = <0>;
+            #address-cells = <1>;
+            #size-cells = <0>;
 
-              csi2_0: port@0 {
-                    reg = <0>;
-                    csi2_phy0: endpoint {
-                           remote-endpoint = <&csi2_cam0>;
-                           clock-lanes = <0>;
-                           data-lanes = <1 2>;
-                    };
-              };
+            csi2_0: port@0 {
+                reg = <0>;
+                csi2_phy0: endpoint {
+                    remote-endpoint = <&csi2_cam0>;
+                    clock-lanes = <0>;
+                    data-lanes = <1 2>;
+                };
+            };
         };
     };

@@ -156,21 +156,21 @@ examples:
         #size-cells = <0>;
 
         camera-sensor@3c {
-               compatible = "ovti,ov5640";
-               reg = <0x3c>;
-               AVDD-supply = <&reg_2p8v>;
-               DOVDD-supply = <&reg_1p8v>;
-               DVDD-supply = <&reg_1p5v>;
-               clocks = <&clk_ov5640_fixed>;
-               clock-names = "xclk";
+            compatible = "ovti,ov5640";
+            reg = <0x3c>;
+            AVDD-supply = <&reg_2p8v>;
+            DOVDD-supply = <&reg_1p8v>;
+            DVDD-supply = <&reg_1p5v>;
+            clocks = <&clk_ov5640_fixed>;
+            clock-names = "xclk";
 
-               port {
-                    csi2_cam0: endpoint {
-                            remote-endpoint = <&csi2_phy0>;
-                            clock-lanes = <0>;
-                            data-lanes = <1 2>;
-                    };
-               };
+            port {
+                csi2_cam0: endpoint {
+                    remote-endpoint = <&csi2_phy0>;
+                    clock-lanes = <0>;
+                    data-lanes = <1 2>;
+                };
+            };
         };
     };

-- 
2.53.0

`h`	back out one level
`j`	next message in thread
`k`	previous message in thread
`l`	drill in
`Esc`	close help / fold thread tree
`?`	toggle this help