Subject: [PATCH net-next v7 0/6] MediaTek Ethernet Patches on MT8195

@@ -1,91 +0,0 @@
-MediaTek DWMAC glue layer controller
-
-This file documents platform glue layer for stmmac.
-Please see stmmac.txt for the other unchanged properties.
-
-The device node has following properties.
-
-Required properties:
-- compatible:  Should be "mediatek,mt2712-gmac" for MT2712 SoC
-- reg:  Address and length of the register set for the device
-- interrupts:  Should contain the MAC interrupts
-- interrupt-names: Should contain a list of interrupt names corresponding to
-	the interrupts in the interrupts property, if available.
-	Should be "macirq" for the main MAC IRQ
-- clocks: Must contain a phandle for each entry in clock-names.
-- clock-names: The name of the clock listed in the clocks property. These are
-	"axi", "apb", "mac_main", "ptp_ref", "rmii_internal" for MT2712 SoC.
-- mac-address: See ethernet.txt in the same directory
-- phy-mode: See ethernet.txt in the same directory
-- mediatek,pericfg: A phandle to the syscon node that control ethernet
-	interface and timing delay.
-
-Optional properties:
-- mediatek,tx-delay-ps: TX clock delay macro value. Default is 0.
-	It should be defined for RGMII/MII interface.
-	It should be defined for RMII interface when the reference clock is from MT2712 SoC.
-- mediatek,rx-delay-ps: RX clock delay macro value. Default is 0.
-	It should be defined for RGMII/MII interface.
-	It should be defined for RMII interface.
-Both delay properties need to be a multiple of 170 for RGMII interface,
-or will round down. Range 0~31*170.
-Both delay properties need to be a multiple of 550 for MII/RMII interface,
-or will round down. Range 0~31*550.
-
-- mediatek,rmii-rxc: boolean property, if present indicates that the RMII
-	reference clock, which is from external PHYs, is connected to RXC pin
-	on MT2712 SoC.
-	Otherwise, is connected to TXC pin.
-- mediatek,rmii-clk-from-mac: boolean property, if present indicates that
-	MT2712 SoC provides the RMII reference clock, which outputs to TXC pin only.
-- mediatek,txc-inverse: boolean property, if present indicates that
-	1. tx clock will be inversed in MII/RGMII case,
-	2. tx clock inside MAC will be inversed relative to reference clock
-	   which is from external PHYs in RMII case, and it rarely happen.
-	3. the reference clock, which outputs to TXC pin will be inversed in RMII case
-	   when the reference clock is from MT2712 SoC.
-- mediatek,rxc-inverse: boolean property, if present indicates that
-	1. rx clock will be inversed in MII/RGMII case.
-	2. reference clock will be inversed when arrived at MAC in RMII case, when
-	   the reference clock is from external PHYs.
-	3. the inside clock, which be sent to MAC, will be inversed in RMII case when
-	   the reference clock is from MT2712 SoC.
-- assigned-clocks: mac_main and ptp_ref clocks
-- assigned-clock-parents: parent clocks of the assigned clocks
-
-Example:
-	eth: ethernet@1101c000 {
-		compatible = "mediatek,mt2712-gmac";
-		reg = <0 0x1101c000 0 0x1300>;
-		interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-names = "macirq";
-		phy-mode ="rgmii-rxid";
-		mac-address = [00 55 7b b5 7d f7];
-		clock-names = "axi",
-			      "apb",
-			      "mac_main",
-			      "ptp_ref",
-			      "rmii_internal";
-		clocks = <&pericfg CLK_PERI_GMAC>,
-			 <&pericfg CLK_PERI_GMAC_PCLK>,
-			 <&topckgen CLK_TOP_ETHER_125M_SEL>,
-			 <&topckgen CLK_TOP_ETHER_50M_SEL>,
-			 <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
-		assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
-				  <&topckgen CLK_TOP_ETHER_50M_SEL>,
-				  <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
-		assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
-					 <&topckgen CLK_TOP_APLL1_D3>,
-					 <&topckgen CLK_TOP_ETHERPLL_50M>;
-		power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
-		mediatek,pericfg = <&pericfg>;
-		mediatek,tx-delay-ps = <1530>;
-		mediatek,rx-delay-ps = <1530>;
-		mediatek,rmii-rxc;
-		mediatek,txc-inverse;
-		mediatek,rxc-inverse;
-		snps,txpbl = <1>;
-		snps,rxpbl = <1>;
-		snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
-		snps,reset-active-low;
-	};

@@ -0,0 +1,156 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mediatek-dwmac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek DWMAC glue layer controller
+
+maintainers:
+  - Biao Huang <biao.huang@mediatek.com>
+
+description:
+  This file documents platform glue layer for stmmac.
+
+# We need a select here so we don't match all nodes with 'snps,dwmac'
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - mediatek,mt2712-gmac
+  required:
+    - compatible
+
+allOf:
+  - $ref: "snps,dwmac.yaml#"
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - mediatek,mt2712-gmac
+          - const: snps,dwmac-4.20a
+
+  clocks:
+    items:
+      - description: AXI clock
+      - description: APB clock
+      - description: MAC Main clock
+      - description: PTP clock
+      - description: RMII reference clock provided by MAC
+
+  clock-names:
+    items:
+      - const: axi
+      - const: apb
+      - const: mac_main
+      - const: ptp_ref
+      - const: rmii_internal
+
+  mediatek,pericfg:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      The phandle to the syscon node that control ethernet
+      interface and timing delay.
+
+  mediatek,tx-delay-ps:
+    description:
+      The internal TX clock delay (provided by this driver) in nanoseconds.
+      For MT2712 RGMII interface, Allowed value need to be a multiple of 170,
+      or will round down. Range 0~31*170.
+      For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
+      or will round down. Range 0~31*550.
+
+  mediatek,rx-delay-ps:
+    description:
+      The internal RX clock delay (provided by this driver) in nanoseconds.
+      For MT2712 RGMII interface, Allowed value need to be a multiple of 170,
+      or will round down. Range 0~31*170.
+      For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
+      or will round down. Range 0~31*550.
+
+  mediatek,rmii-rxc:
+    type: boolean
+    description:
+      If present, indicates that the RMII reference clock, which is from external
+      PHYs, is connected to RXC pin. Otherwise, is connected to TXC pin.
+
+  mediatek,rmii-clk-from-mac:
+    type: boolean
+    description:
+      If present, indicates that MAC provides the RMII reference clock, which
+      outputs to TXC pin only.
+
+  mediatek,txc-inverse:
+    type: boolean
+    description:
+      If present, indicates that
+      1. tx clock will be inversed in MII/RGMII case,
+      2. tx clock inside MAC will be inversed relative to reference clock
+         which is from external PHYs in RMII case, and it rarely happen.
+      3. the reference clock, which outputs to TXC pin will be inversed in RMII case
+         when the reference clock is from MAC.
+
+  mediatek,rxc-inverse:
+    type: boolean
+    description:
+      If present, indicates that
+      1. rx clock will be inversed in MII/RGMII case.
+      2. reference clock will be inversed when arrived at MAC in RMII case, when
+         the reference clock is from external PHYs.
+      3. the inside clock, which be sent to MAC, will be inversed in RMII case when
+         the reference clock is from MAC.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - phy-mode
+  - mediatek,pericfg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt2712-clk.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/power/mt2712-power.h>
+
+    eth: ethernet@1101c000 {
+        compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
+        reg = <0x1101c000 0x1300>;
+        interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
+        interrupt-names = "macirq";
+        phy-mode ="rgmii-rxid";
+        mac-address = [00 55 7b b5 7d f7];
+        clock-names = "axi",
+                      "apb",
+                      "mac_main",
+                      "ptp_ref",
+                      "rmii_internal";
+        clocks = <&pericfg CLK_PERI_GMAC>,
+                 <&pericfg CLK_PERI_GMAC_PCLK>,
+                 <&topckgen CLK_TOP_ETHER_125M_SEL>,
+                 <&topckgen CLK_TOP_ETHER_50M_SEL>,
+                 <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
+        assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
+                          <&topckgen CLK_TOP_ETHER_50M_SEL>,
+                          <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
+        assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
+                                 <&topckgen CLK_TOP_APLL1_D3>,
+                                 <&topckgen CLK_TOP_ETHERPLL_50M>;
+        power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
+        mediatek,pericfg = <&pericfg>;
+        mediatek,tx-delay-ps = <1530>;
+        snps,txpbl = <1>;
+        snps,rxpbl = <1>;
+        snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+        snps,reset-delays-us = <0 10000 10000>;
+    };

@@ -39,6 +39,33 @@
 #define ETH_FINE_DLY_GTXC	BIT(1)
 #define ETH_FINE_DLY_RXC	BIT(0)
 
+/* Peri Configuration register for mt8195 */
+#define MT8195_PERI_ETH_CTRL0		0xFD0
+#define MT8195_RMII_CLK_SRC_INTERNAL	BIT(28)
+#define MT8195_RMII_CLK_SRC_RXC		BIT(27)
+#define MT8195_ETH_INTF_SEL		GENMASK(26, 24)
+#define MT8195_RGMII_TXC_PHASE_CTRL	BIT(22)
+#define MT8195_EXT_PHY_MODE		BIT(21)
+#define MT8195_DLY_GTXC_INV		BIT(12)
+#define MT8195_DLY_GTXC_ENABLE		BIT(5)
+#define MT8195_DLY_GTXC_STAGES		GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL1		0xFD4
+#define MT8195_DLY_RXC_INV		BIT(25)
+#define MT8195_DLY_RXC_ENABLE		BIT(18)
+#define MT8195_DLY_RXC_STAGES		GENMASK(17, 13)
+#define MT8195_DLY_TXC_INV		BIT(12)
+#define MT8195_DLY_TXC_ENABLE		BIT(5)
+#define MT8195_DLY_TXC_STAGES		GENMASK(4, 0)
+
+#define MT8195_PERI_ETH_CTRL2		0xFD8
+#define MT8195_DLY_RMII_RXC_INV		BIT(25)
+#define MT8195_DLY_RMII_RXC_ENABLE	BIT(18)
+#define MT8195_DLY_RMII_RXC_STAGES	GENMASK(17, 13)
+#define MT8195_DLY_RMII_TXC_INV		BIT(12)
+#define MT8195_DLY_RMII_TXC_ENABLE	BIT(5)
+#define MT8195_DLY_RMII_TXC_STAGES	GENMASK(4, 0)
+
 struct mac_delay_struct {
 	u32 tx_delay;
 	u32 rx_delay;

@@ -57,11 +84,13 @@ struct mediatek_dwmac_plat_data {
 	int num_clks_to_config;
 	bool rmii_clk_from_mac;
 	bool rmii_rxc;
+	bool mac_wol;
 };
 
 struct mediatek_dwmac_variant {
 	int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data *plat);
 	int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
+	void (*dwmac_fix_mac_speed)(void *priv, unsigned int speed);
 
 	/* clock ids to be requested */
 	const char * const *clk_list;

@@ -77,6 +106,10 @@ static const char * const mt2712_dwmac_clk_l[] = {
 	"axi", "apb", "mac_main", "ptp_ref", "rmii_internal"
 };
 
+static const char * const mt8195_dwmac_clk_l[] = {
+	"axi", "apb", "mac_cg", "mac_main", "ptp_ref", "rmii_internal"
+};
+
 static int mt2712_set_interface(struct mediatek_dwmac_plat_data *plat)
 {
 	int rmii_clk_from_mac = plat->rmii_clk_from_mac ? RMII_CLK_SRC_INTERNAL : 0;

@@ -267,6 +300,204 @@ static const struct mediatek_dwmac_variant mt2712_gmac_variant = {
 		.tx_delay_max = 17600,
 };
 
+static int mt8195_set_interface(struct mediatek_dwmac_plat_data *plat)
+{
+	int rmii_clk_from_mac = plat->rmii_clk_from_mac ? MT8195_RMII_CLK_SRC_INTERNAL : 0;
+	int rmii_rxc = plat->rmii_rxc ? MT8195_RMII_CLK_SRC_RXC : 0;
+	u32 intf_val = 0;
+
+	/* The clock labeled as "rmii_internal" in mt8195_dwmac_clk_l is needed
+	 * only in RMII(when MAC provides the reference clock), and useless for
+	 * RGMII/MII/RMII(when PHY provides the reference clock).
+	 * num_clks_to_config indicates the real number of clocks should be
+	 * configured, equals to (plat->variant->num_clks - 1) in default for all the case,
+	 * then +1 for rmii_clk_from_mac case.
+	 */
+	plat->num_clks_to_config = plat->variant->num_clks - 1;
+
+	/* select phy interface in top control domain */
+	switch (plat->phy_mode) {
+	case PHY_INTERFACE_MODE_MII:
+		intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_MII);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (plat->rmii_clk_from_mac)
+			plat->num_clks_to_config++;
+		intf_val |= (rmii_rxc | rmii_clk_from_mac);
+		intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RMII);
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+		intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL, PHY_INTF_RGMII);
+		break;
+	default:
+		dev_err(plat->dev, "phy interface not supported\n");
+		return -EINVAL;
+	}
+
+	/* MT8195 only support external PHY */
+	intf_val |= MT8195_EXT_PHY_MODE;
+
+	regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL0, intf_val);
+
+	return 0;
+}
+
+static void mt8195_delay_ps2stage(struct mediatek_dwmac_plat_data *plat)
+{
+	struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+	/* 290ps per stage */
+	mac_delay->tx_delay /= 290;
+	mac_delay->rx_delay /= 290;
+}
+
+static void mt8195_delay_stage2ps(struct mediatek_dwmac_plat_data *plat)
+{
+	struct mac_delay_struct *mac_delay = &plat->mac_delay;
+
+	/* 290ps per stage */
+	mac_delay->tx_delay *= 290;
+	mac_delay->rx_delay *= 290;
+}
+
+static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
+{
+	struct mac_delay_struct *mac_delay = &plat->mac_delay;
+	u32 gtxc_delay_val = 0, delay_val = 0, rmii_delay_val = 0;
+
+	mt8195_delay_ps2stage(plat);
+
+	switch (plat->phy_mode) {
+	case PHY_INTERFACE_MODE_MII:
+		delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE, !!mac_delay->tx_delay);
+		delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES, mac_delay->tx_delay);
+		delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV, mac_delay->tx_inv);
+
+		delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+		delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+		delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+		break;
+	case PHY_INTERFACE_MODE_RMII:
+		if (plat->rmii_clk_from_mac) {
+			/* case 1: mac provides the rmii reference clock,
+			 * and the clock output to TXC pin.
+			 * The egress timing can be adjusted by RMII_TXC delay macro circuit.
+			 * The ingress timing can be adjusted by RMII_RXC delay macro circuit.
+			 */
+			rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_ENABLE,
+						     !!mac_delay->tx_delay);
+			rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_STAGES,
+						     mac_delay->tx_delay);
+			rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_TXC_INV,
+						     mac_delay->tx_inv);
+
+			rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_ENABLE,
+						     !!mac_delay->rx_delay);
+			rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_STAGES,
+						     mac_delay->rx_delay);
+			rmii_delay_val |= FIELD_PREP(MT8195_DLY_RMII_RXC_INV,
+						     mac_delay->rx_inv);
+		} else {
+			/* case 2: the rmii reference clock is from external phy,
+			 * and the property "rmii_rxc" indicates which pin(TXC/RXC)
+			 * the reference clk is connected to. The reference clock is a
+			 * received signal, so rx_delay/rx_inv are used to indicate
+			 * the reference clock timing adjustment
+			 */
+			if (plat->rmii_rxc) {
+				/* the rmii reference clock from outside is connected
+				 * to RXC pin, the reference clock will be adjusted
+				 * by RXC delay macro circuit.
+				 */
+				delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE,
+							!!mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES,
+							mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV,
+							mac_delay->rx_inv);
+			} else {
+				/* the rmii reference clock from outside is connected
+				 * to TXC pin, the reference clock will be adjusted
+				 * by TXC delay macro circuit.
+				 */
+				delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE,
+							!!mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES,
+							mac_delay->rx_delay);
+				delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV,
+							mac_delay->rx_inv);
+			}
+		}
+		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+		gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_ENABLE, !!mac_delay->tx_delay);
+		gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_STAGES, mac_delay->tx_delay);
+		gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_INV, mac_delay->tx_inv);
+
+		delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE, !!mac_delay->rx_delay);
+		delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES, mac_delay->rx_delay);
+		delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay->rx_inv);
+
+		break;
+	default:
+		dev_err(plat->dev, "phy interface not supported\n");
+		return -EINVAL;
+	}
+
+	regmap_update_bits(plat->peri_regmap,
+			   MT8195_PERI_ETH_CTRL0,
+			   MT8195_RGMII_TXC_PHASE_CTRL |
+			   MT8195_DLY_GTXC_INV |
+			   MT8195_DLY_GTXC_ENABLE |
+			   MT8195_DLY_GTXC_STAGES,
+			   gtxc_delay_val);
+	regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL1, delay_val);
+	regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL2, rmii_delay_val);
+
+	mt8195_delay_stage2ps(plat);
+
+	return 0;
+}
+
+static void mt8195_fix_mac_speed(void *priv, unsigned int speed)
+{
+	struct mediatek_dwmac_plat_data *priv_plat = priv;
+
+	if ((phy_interface_mode_is_rgmii(priv_plat->phy_mode))) {
+		/* prefer 2ns fixed delay which is controlled by TXC_PHASE_CTRL,
+		 * when link speed is 1Gbps with RGMII interface,
+		 * Fall back to delay macro circuit for 10/100Mbps link speed.
+		 */
+		if (speed == SPEED_1000)
+			regmap_update_bits(priv_plat->peri_regmap,
+					   MT8195_PERI_ETH_CTRL0,
+					   MT8195_RGMII_TXC_PHASE_CTRL |
+					   MT8195_DLY_GTXC_ENABLE |
+					   MT8195_DLY_GTXC_INV |
+					   MT8195_DLY_GTXC_STAGES,
+					   MT8195_RGMII_TXC_PHASE_CTRL);
+		else
+			mt8195_set_delay(priv_plat);
+	}
+}
+
+static const struct mediatek_dwmac_variant mt8195_gmac_variant = {
+	.dwmac_set_phy_interface = mt8195_set_interface,
+	.dwmac_set_delay = mt8195_set_delay,
+	.dwmac_fix_mac_speed = mt8195_fix_mac_speed,
+	.clk_list = mt8195_dwmac_clk_l,
+	.num_clks = ARRAY_SIZE(mt8195_dwmac_clk_l),
+	.dma_bit_mask = 35,
+	.rx_delay_max = 9280,
+	.tx_delay_max = 9280,
+};
+
 static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
 {
 	struct mac_delay_struct *mac_delay = &plat->mac_delay;

@@ -307,6 +538,7 @@ static int mediatek_dwmac_config_dt(struct mediatek_dwmac_plat_data *plat)
 	mac_delay->rx_inv = of_property_read_bool(plat->np, "mediatek,rxc-inverse");
 	plat->rmii_rxc = of_property_read_bool(plat->np, "mediatek,rmii-rxc");
 	plat->rmii_clk_from_mac = of_property_read_bool(plat->np, "mediatek,rmii-clk-from-mac");
+	plat->mac_wol = of_property_read_bool(plat->np, "mediatek,mac-wol");
 
 	return 0;
 }

@@ -383,6 +615,7 @@ static int mediatek_dwmac_clks_config(void *priv, bool enabled)
 
 	return ret;
 }
+
 static int mediatek_dwmac_probe(struct platform_device *pdev)
 {
 	struct mediatek_dwmac_plat_data *priv_plat;

@@ -420,7 +653,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
 		return PTR_ERR(plat_dat);
 
 	plat_dat->interface = priv_plat->phy_mode;
-	plat_dat->use_phy_wol = 1;
+	plat_dat->use_phy_wol = priv_plat->mac_wol ? 0 : 1;
 	plat_dat->riwt_off = 1;
 	plat_dat->maxmtu = ETH_DATA_LEN;
 	plat_dat->addr64 = priv_plat->variant->dma_bit_mask;

@@ -428,7 +661,23 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
 	plat_dat->init = mediatek_dwmac_init;
 	plat_dat->exit = mediatek_dwmac_exit;
 	plat_dat->clks_config = mediatek_dwmac_clks_config;
+	if (priv_plat->variant->dwmac_fix_mac_speed)
+		plat_dat->fix_mac_speed = priv_plat->variant->dwmac_fix_mac_speed;
+	plat_dat->safety_feat_cfg = devm_kzalloc(&pdev->dev,
+						 sizeof(*plat_dat->safety_feat_cfg),
+						 GFP_KERNEL);
+	if (!plat_dat->safety_feat_cfg)
+		return -ENOMEM;
 
+	plat_dat->safety_feat_cfg->tsoee = 1;
+	plat_dat->safety_feat_cfg->mrxpee = 0;
+	plat_dat->safety_feat_cfg->mestee = 1;
+	plat_dat->safety_feat_cfg->mrxee = 1;
+	plat_dat->safety_feat_cfg->mtxee = 1;
+	plat_dat->safety_feat_cfg->epsi = 0;
+	plat_dat->safety_feat_cfg->edpp = 1;
+	plat_dat->safety_feat_cfg->prtyen = 1;
+	plat_dat->safety_feat_cfg->tmouten = 1;
 	mediatek_dwmac_init(pdev, priv_plat);
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);

@@ -443,6 +692,8 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
 static const struct of_device_id mediatek_dwmac_match[] = {
 	{ .compatible = "mediatek,mt2712-gmac",
 	  .data = &mt2712_gmac_variant },
+	{ .compatible = "mediatek,mt8195-gmac",
+	  .data = &mt8195_gmac_variant },
 	{ }
 };
 

@@ -110,6 +110,7 @@ &eth {
 	phy-handle = <&ethernet_phy0>;
 	mediatek,tx-delay-ps = <1530>;
 	snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+	snps,reset-delays-us = <0 10000 10000>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&eth_default>;
 	pinctrl-1 = <&eth_sleep>;

@@ -726,7 +726,7 @@ queue2 {
 	};
 
 	eth: ethernet@1101c000 {
-		compatible = "mediatek,mt2712-gmac";
+		compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
 		reg = <0 0x1101c000 0 0x1300>;
 		interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "macirq";

@@ -734,15 +734,19 @@ eth: ethernet@1101c000 {
 		clock-names = "axi",
 			      "apb",
 			      "mac_main",
-			      "ptp_ref";
+			      "ptp_ref",
+			      "rmii_internal";
 		clocks = <&pericfg CLK_PERI_GMAC>,
 			 <&pericfg CLK_PERI_GMAC_PCLK>,
 			 <&topckgen CLK_TOP_ETHER_125M_SEL>,
-			 <&topckgen CLK_TOP_ETHER_50M_SEL>;
+			 <&topckgen CLK_TOP_ETHER_50M_SEL>,
+			 <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
 		assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
-				  <&topckgen CLK_TOP_ETHER_50M_SEL>;
+				  <&topckgen CLK_TOP_ETHER_50M_SEL>,
+				  <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
 		assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
-					 <&topckgen CLK_TOP_APLL1_D3>;
+					 <&topckgen CLK_TOP_APLL1_D3>,
+					 <&topckgen CLK_TOP_ETHERPLL_50M>;
 		power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
 		mediatek,pericfg = <&pericfg>;
 		snps,axi-config = <&stmmac_axi_setup>;

@@ -9,7 +9,6 @@
 #include <linux/of.h>
 #include <linux/of_device.h>
 #include <linux/of_net.h>
-#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/stmmac.h>
 

@@ -359,9 +358,6 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
 		return ret;
 	}
 
-	pm_runtime_enable(&pdev->dev);
-	pm_runtime_get_sync(&pdev->dev);
-
 	return 0;
 }
 

@@ -370,11 +366,25 @@ static void mediatek_dwmac_exit(struct platform_device *pdev, void *priv)
 	struct mediatek_dwmac_plat_data *plat = priv;
 
 	clk_bulk_disable_unprepare(plat->num_clks_to_config, plat->clks);
-
-	pm_runtime_put_sync(&pdev->dev);
-	pm_runtime_disable(&pdev->dev);
 }
 
+static int mediatek_dwmac_clks_config(void *priv, bool enabled)
+{
+	struct mediatek_dwmac_plat_data *plat = priv;
+	int ret = 0;
+
+	if (enabled) {
+		ret = clk_bulk_prepare_enable(plat->num_clks_to_config, plat->clks);
+		if (ret) {
+			dev_err(plat->dev, "failed to enable clks, err = %d\n", ret);
+			return ret;
+		}
+	} else {
+		clk_bulk_disable_unprepare(plat->num_clks_to_config, plat->clks);
+	}
+
+	return ret;
+}
 static int mediatek_dwmac_probe(struct platform_device *pdev)
 {
 	struct mediatek_dwmac_plat_data *priv_plat;

@@ -420,6 +430,7 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
 	plat_dat->bsp_priv = priv_plat;
 	plat_dat->init = mediatek_dwmac_init;
 	plat_dat->exit = mediatek_dwmac_exit;
+	plat_dat->clks_config = mediatek_dwmac_clks_config;
 	mediatek_dwmac_init(pdev, priv_plat);
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);

@@ -334,22 +334,20 @@ static int mediatek_dwmac_init(struct platform_device *pdev, void *priv)
 	const struct mediatek_dwmac_variant *variant = plat->variant;
 	int ret;
 
-	ret = dma_set_mask_and_coherent(plat->dev, DMA_BIT_MASK(variant->dma_bit_mask));
-	if (ret) {
-		dev_err(plat->dev, "No suitable DMA available, err = %d\n", ret);
-		return ret;
-	}
-
-	ret = variant->dwmac_set_phy_interface(plat);
-	if (ret) {
-		dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret);
-		return ret;
+	if (variant->dwmac_set_phy_interface) {
+		ret = variant->dwmac_set_phy_interface(plat);
+		if (ret) {
+			dev_err(plat->dev, "failed to set phy interface, err = %d\n", ret);
+			return ret;
+		}
 	}
 
-	ret = variant->dwmac_set_delay(plat);
-	if (ret) {
-		dev_err(plat->dev, "failed to set delay value, err = %d\n", ret);
-		return ret;
+	if (variant->dwmac_set_delay) {
+		ret = variant->dwmac_set_delay(plat);
+		if (ret) {
+			dev_err(plat->dev, "failed to set delay value, err = %d\n", ret);
+			return ret;
+		}
 	}
 
 	ret = clk_bulk_prepare_enable(plat->num_clks_to_config, plat->clks);

@@ -422,15 +420,15 @@ static int mediatek_dwmac_probe(struct platform_device *pdev)
 		return PTR_ERR(plat_dat);
 
 	plat_dat->interface = priv_plat->phy_mode;
-	plat_dat->has_gmac4 = 1;
-	plat_dat->has_gmac = 0;
-	plat_dat->pmt = 0;
+	plat_dat->use_phy_wol = 1;
 	plat_dat->riwt_off = 1;
 	plat_dat->maxmtu = ETH_DATA_LEN;
+	plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
 	plat_dat->bsp_priv = priv_plat;
 	plat_dat->init = mediatek_dwmac_init;
 	plat_dat->exit = mediatek_dwmac_exit;
 	plat_dat->clks_config = mediatek_dwmac_clks_config;
+
 	mediatek_dwmac_init(pdev, priv_plat);
 
 	ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);

@@ -19,11 +19,67 @@ select:
       contains:
         enum:
           - mediatek,mt2712-gmac
+          - mediatek,mt8195-gmac
   required:
     - compatible
 
 allOf:
   - $ref: "snps,dwmac.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt2712-gmac
+
+    then:
+      properties:
+        clocks:
+          minItems: 5
+          items:
+            - description: AXI clock
+            - description: APB clock
+            - description: MAC Main clock
+            - description: PTP clock
+            - description: RMII reference clock provided by MAC
+
+        clock-names:
+          minItems: 5
+          items:
+            - const: axi
+            - const: apb
+            - const: mac_main
+            - const: ptp_ref
+            - const: rmii_internal
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - mediatek,mt8195-gmac
+
+    then:
+      properties:
+        clocks:
+          minItems: 6
+          items:
+            - description: AXI clock
+            - description: APB clock
+            - description: MAC clock gate
+            - description: MAC Main clock
+            - description: PTP clock
+            - description: RMII reference clock provided by MAC
+
+        clock-names:
+          minItems: 6
+          items:
+            - const: axi
+            - const: apb
+            - const: mac_cg
+            - const: mac_main
+            - const: ptp_ref
+            - const: rmii_internal
 
 properties:
   compatible:

@@ -32,22 +88,10 @@ properties:
           - enum:
               - mediatek,mt2712-gmac
           - const: snps,dwmac-4.20a
-
-  clocks:
-    items:
-      - description: AXI clock
-      - description: APB clock
-      - description: MAC Main clock
-      - description: PTP clock
-      - description: RMII reference clock provided by MAC
-
-  clock-names:
-    items:
-      - const: axi
-      - const: apb
-      - const: mac_main
-      - const: ptp_ref
-      - const: rmii_internal
+      - items:
+          - enum:
+              - mediatek,mt8195-gmac
+          - const: snps,dwmac-5.10a
 
   mediatek,pericfg:
     $ref: /schemas/types.yaml#/definitions/phandle

@@ -62,6 +106,8 @@ properties:
       or will round down. Range 0~31*170.
       For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
       or will round down. Range 0~31*550.
+      For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290,
+      or will round down. Range 0~31*290.
 
   mediatek,rx-delay-ps:
     description:

@@ -70,6 +116,8 @@ properties:
       or will round down. Range 0~31*170.
       For MT2712 RMII/MII interface, Allowed value need to be a multiple of 550,
       or will round down. Range 0~31*550.
+      For MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple
+      of 290, or will round down. Range 0~31*290.
 
   mediatek,rmii-rxc:
     type: boolean

@@ -103,6 +151,12 @@ properties:
       3. the inside clock, which be sent to MAC, will be inversed in RMII case when
          the reference clock is from MAC.
 
+  mediatek,mac-wol:
+    type: boolean
+    description:
+      If present, indicates that MAC supports WOL(Wake-On-LAN), and MAC WOL will be enabled.
+      Otherwise, PHY WOL is perferred.
+
 required:
   - compatible
   - reg