[PATCH 1/2] ARM: dts: imx: change the spi-nor tx

Subsystems: the rest

STALE1773d

3 messages, 2 authors, 2021-10-04 · open the first message on its own page

[PATCH 1/2] ARM: dts: imx: change the spi-nor tx

From: haibo.chen@nxp.com
Date: 2021-08-20 09:51:59 

From: Haibo Chen <haibo.chen@nxp.com>

Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
 arch/arm/boot/dts/imx6sx-sdb.dts        | 4 ++--
 arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 5a63ca615722..99f4cf777a38 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -114,7 +114,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 
@@ -124,7 +124,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <2>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index 779cc536566d..a3fde3316c73 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -292,7 +292,7 @@
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		reg = <0>;
 	};
 };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/2] arm64: dts: imx8: change the spi-nor tx

From: haibo.chen@nxp.com
Date: 2021-08-20 09:52:00 

From: Haibo Chen <haibo.chen@nxp.com>

Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

qspi and fspi host controller do not support read 1-4-4 mode. so need to
set the tx to 1, let the common code finally select read 1-1-4 mode.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi        | 2 +-
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts                | 2 +-
 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi        | 2 +-
 arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi       | 2 +-
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts                | 2 ++
 arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts | 2 +-
 6 files changed, 7 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
index 988f8ab679ad..40f5e7a3b064 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
@@ -91,7 +91,7 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index 4e2820d19244..a2b24d4d4e3e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -48,7 +48,7 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
index 54eaf3d6055b..3b2d627a0342 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
@@ -101,7 +101,7 @@
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
index aa78e0d8c72b..fc178eebf8aa 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
@@ -74,7 +74,7 @@
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <80000000>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index 49f9db971f3b..b83df77195ec 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -337,6 +337,8 @@
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
index f593e4ff62e1..564746d5000d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
@@ -281,7 +281,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
-		spi-tx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 		spi-max-frequency = <50000000>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/2] ARM: dts: imx: change the spi-nor tx

From: Shawn Guo <shawnguo@kernel.org>
Date: 2021-10-04 03:26:05 

On Fri, Aug 20, 2021 at 05:29:49PM +0800, haibo.chen@nxp.com wrote:
From: Haibo Chen <haibo.chen@nxp.com>

Before commit 0e30f47232ab5 ("mtd: spi-nor: add support for DTR protocol"),
for all PP command, it only support 1-1-1 mode, no matter the tx setting
in dts. But after the upper commit, the logic change. It will choose
the best mode(fastest mode) which flash device and spi-nor host controller
both support.

Though the spi-nor device on imx6sx-sdb/imx6ul(l/z)-14x14-evk board
do not support PP-1-4-4/PP-1-1-4, but if tx is 4 in dts file, it will also
impact the read mode selection. For the spi-nor device on the upper mentioned
boards, they support read 1-4-4 mode and read 1-1-4 mode according to the
device internal sfdp register. But qspi host controller do not support
read 1-4-4 mode. so need to set the tx to 1, let the common code finally
select read 1-1-4 mode, PP-1-1-1 mode.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Applied both, thanks!

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help