[PATCH] ARM: dts: ixp4xx: Add devicetree for Iomega NAS 100D

@@ -240,6 +240,7 @@ dtb-$(CONFIG_ARCH_INTEGRATOR) += \
 	integratorcp.dtb
 dtb-$(CONFIG_ARCH_IXP4XX) += \
 	intel-ixp42x-linksys-nslu2.dtb \
+	intel-ixp42x-iomega-nas100d.dtb \
 	intel-ixp43x-gateworks-gw2358.dtb
 dtb-$(CONFIG_ARCH_KEYSTONE) += \
 	keystone-k2hk-evm.dtb \

@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Iomega NAS 100D
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Iomega NAS 100D";
+	compatible = "iom,nas-100d", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 64 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led-wlan {
+			label = "nas100d:red:wlan";
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			/* We don't have WLAN trigger in the kernel (yet) */
+			linux,default-trigger = "netdev";
+		};
+		led-disk {
+			label = "nas100d:red:disk";
+			gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "disk-activity";
+		};
+		led-power {
+			label = "nas100d:red:power";
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		button-power {
+			wakeup-source;
+			linux,code = <KEY_POWER>;
+			label = "power";
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		};
+		button-reset {
+			wakeup-source;
+			linux,code = <KEY_ESC>;
+			label = "reset";
+			gpios = <&gpio0 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rtc@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		timeout-ms = <5000>;
+	};
+
+	soc {
+		bus@50000000 {
+			/* The first 16MB region at CS0 on the expansion bus */
+			flash@0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 0x20000 byte blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0x00000000 0x800000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x7e0000 */
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * Taken from NAS 100D PCI boardfile (nas100d-pci.c)
+			 * We have slots (IDSEL) 1, 2 and 3 and pins 1, 2 and 3.
+			 */
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 3>, /* INT A on slot 1 is irq 11 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 3>, /* INT A on slot 2 is irq 10 */
+			/* IDSEL 3 */
+			<0x1800 0 0 1 &gpio0 9  3>, /* INT A on slot 3 is irq 9 */
+			<0x1800 0 0 2 &gpio0 8  3>, /* INT B on slot 3 is irq 8 */
+			<0x1800 0 0 3 &gpio0 7  3>; /* INT C on slot 3 is irq 7 */
+		};
+
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+			};
+		};
+	};
+};