[PATCH v1 0/6] arm64: dts: librem5-devkit: Improve audio support

STALE2012d

8 messages, 2 authors, 2021-03-07 · open the first message on its own page

[PATCH v1 0/6] arm64: dts: librem5-devkit: Improve audio support

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:08:17 

So far only headphone output worked. Thesse patches add support for the
built in speaker and mic, allow a headset microphone to work and wire up jack
detection so audio output can switch to headphones automatically.  They also
adjust the card name to match the board not the codec, similar what's done for
the Librem 5.

Patches are against next-20210210 but also apply against Shawn's imx-dt64-5.12

Guido Günther (6):
  arm64: dts: librem5-devkit: Use a less generic codec name
  arm64: dts: librem5-devkit: Add speaker amplifier
  arm64: dts: librem5-devkit: "Drop Line In Jack"
  arm64: defconfig: Enable asoc simple mux
  arm64: dts: librem5-devkit: Add mux for built-in vs headset mic
  arm64: dts: librem5-devkit: Move headphone detection to sound card

 .../dts/freescale/imx8mq-librem5-devkit.dts   | 69 ++++++++++++++-----
 arch/arm64/configs/defconfig                  |  1 +
 2 files changed, 52 insertions(+), 18 deletions(-)

-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 1/6] arm64: dts: librem5-devkit: Use a less generic codec name

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:08:16 

The codec is currently named after the chip but it should be named like
the device itself since otherwise it's impossible to distinguish it from
other devices using the same codec (e.g. in alsa's UCM).

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index dd217a0760e9..0c0b12c90363 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -165,7 +165,7 @@ wwan_codec: sound-wwan-codec {
 
 	sound {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "sgtl5000";
+		simple-audio-card,name = "Librem 5 Devkit";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,widgets =
 			"Microphone", "Microphone Jack",
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 2/6] arm64: dts: librem5-devkit: Add speaker amplifier

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:08:16 

Wire up the amplifier that drives the builtin speaker.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 21 +++++++++++++++++--
 1 file changed, 19 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 0c0b12c90363..d01bed5eb9e0 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -165,19 +165,21 @@ wwan_codec: sound-wwan-codec {
 
 	sound {
 		compatible = "simple-audio-card";
+		simple-audio-card,aux-devs = <&speaker_amp>;
 		simple-audio-card,name = "Librem 5 Devkit";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,widgets =
 			"Microphone", "Microphone Jack",
 			"Headphone", "Headphone Jack",
-			"Speaker", "Speaker Ext",
+			"Speaker", "Builtin Speaker",
 			"Line", "Line In Jack";
 		simple-audio-card,routing =
 			"MIC_IN", "Microphone Jack",
 			"Microphone Jack", "Mic Bias",
 			"LINE_IN", "Line In Jack",
 			"Headphone Jack", "HP_OUT",
-			"Speaker Ext", "LINE_OUT";
+			"Builtin Speaker", "Speaker Amp OUTR",
+			"Speaker Amp INR", "LINE_OUT";
 
 		simple-audio-card,cpu {
 			sound-dai = <&sai2>;
@@ -207,6 +209,15 @@ telephony_link_master: simple-audio-card,codec {
 		};
 	};
 
+	speaker_amp: speaker-amp {
+		compatible = "simple-audio-amplifier";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_spkamp>;
+		VCC-supply = <&reg_3v3_p>;
+		sound-name-prefix = "Speaker Amp";
+		enable-gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+	};
+
 	vibrator {
 		compatible = "gpio-vibrator";
 		pinctrl-names = "default";
@@ -641,6 +652,12 @@ MX8MQ_IOMUXC_SAI5_RXFS_GPIO3_IO19	0x8  /* IMU_INT */
 		>;
 	};
 
+	pinctrl_spkamp: spkamp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SPDIF_TX_GPIO5_IO3		0x81  /* MUTE */
+		>;
+	};
+
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x80  /* PMIC intr */
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 4/6] arm64: defconfig: Enable asoc simple mux

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:08:32 

This is needed to model the mic input mux on the Librem 5 devkit.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index e830d1be6f27..762fb6a132df 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -790,6 +790,7 @@ CONFIG_SND_SOC_GTM601=m
 CONFIG_SND_SOC_PCM3168A_I2C=m
 CONFIG_SND_SOC_RT5659=m
 CONFIG_SND_SOC_SIMPLE_AMPLIFIER=m
+CONFIG_SND_SOC_SIMPLE_MUX=m
 CONFIG_SND_SOC_TAS571X=m
 CONFIG_SND_SOC_WCD934X=m
 CONFIG_SND_SOC_WM8904=m
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 3/6] arm64: dts: librem5-devkit: "Drop Line In Jack"

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:08:33 

The SGTL500s LINEINL and LINEINR are N/C.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 4 +---
 1 file changed, 1 insertion(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index d01bed5eb9e0..aac05bbaa001 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -171,12 +171,10 @@ sound {
 		simple-audio-card,widgets =
 			"Microphone", "Microphone Jack",
 			"Headphone", "Headphone Jack",
-			"Speaker", "Builtin Speaker",
-			"Line", "Line In Jack";
+			"Speaker", "Builtin Speaker";
 		simple-audio-card,routing =
 			"MIC_IN", "Microphone Jack",
 			"Microphone Jack", "Mic Bias",
-			"LINE_IN", "Line In Jack",
 			"Headphone Jack", "HP_OUT",
 			"Builtin Speaker", "Speaker Amp OUTR",
 			"Speaker Amp INR", "LINE_OUT";
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 6/6] arm64: dts: librem5-devkit: Move headphone detection to sound card

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:09:00 

This allows for automatic output source switching in userspace. Enable
the pullup on the GPIO to actually make it trigger and mark it as
active-high since detection is reversed otherwise.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 21 ++++++++++---------
 1 file changed, 11 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index f818af592046..e3bfef98090a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -50,13 +50,6 @@ btn2 {
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		hp-det {
-			label = "HP_DET";
-			gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-			linux,code = <KEY_HP>;
-		};
-
 		wwan-wake {
 			label = "WWAN_WAKE";
 			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
@@ -173,22 +166,25 @@ mic_mux: mic-mux {
 
 	sound {
 		compatible = "simple-audio-card";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hpdet>;
 		simple-audio-card,aux-devs = <&speaker_amp>, <&mic_mux>;
 		simple-audio-card,name = "Librem 5 Devkit";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,widgets =
 			"Microphone", "Builtin Microphone",
 			"Microphone", "Headset Microphone",
-			"Headphone", "Headphone Jack",
+			"Headphone", "Headphones",
 			"Speaker", "Builtin Speaker";
 		simple-audio-card,routing =
 			"MIC_IN", "Mic Mux OUT",
 			"Mic Mux IN1", "Headset Microphone",
 			"Mic Mux IN2", "Builtin Microphone",
 			"Mic Mux OUT", "Mic Bias",
-			"Headphone Jack", "HP_OUT",
+			"Headphones", "HP_OUT",
 			"Builtin Speaker", "Speaker Amp OUTR",
 			"Speaker Amp INR", "LINE_OUT";
+		simple-audio-card,hp-det-gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 
 		simple-audio-card,cpu {
 			sound-dai = <&sai2>;
@@ -630,7 +626,6 @@ pinctrl_gpio_keys: gpiokeygrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x16
 			MX8MQ_IOMUXC_SAI2_RXC_GPIO4_IO22	0x16
-			MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20	0x180  /* HP_DET */
 			MX8MQ_IOMUXC_NAND_DATA02_GPIO3_IO8	0x80   /* nWoWWAN */
 		>;
 	};
@@ -641,6 +636,12 @@ MX8MQ_IOMUXC_SPDIF_RX_GPIO5_IO4		0xc6   /* nHAPTIC */
 		>;
 	};
 
+	pinctrl_hpdet: hpdetgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20	0xC0   /* HP_DET */
+		>;
+	};
+
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL		0x4000001f
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v1 5/6] arm64: dts: librem5-devkit: Add mux for built-in vs headset mic

From: Guido Günther <agx@sigxcpu.org>
Date: 2021-02-21 11:09:00 

Add mux so we can select either headset or built-in microphone input.

Signed-off-by: Guido Günther <agx@sigxcpu.org>
---
 .../dts/freescale/imx8mq-librem5-devkit.dts   | 25 ++++++++++++++++---
 1 file changed, 21 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index aac05bbaa001..f818af592046 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -163,18 +163,29 @@ wwan_codec: sound-wwan-codec {
 		#sound-dai-cells = <0>;
 	};
 
+	mic_mux: mic-mux {
+		compatible = "simple-audio-mux";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_micsel>;
+		mux-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>;
+		sound-name-prefix = "Mic Mux";
+	};
+
 	sound {
 		compatible = "simple-audio-card";
-		simple-audio-card,aux-devs = <&speaker_amp>;
+		simple-audio-card,aux-devs = <&speaker_amp>, <&mic_mux>;
 		simple-audio-card,name = "Librem 5 Devkit";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,widgets =
-			"Microphone", "Microphone Jack",
+			"Microphone", "Builtin Microphone",
+			"Microphone", "Headset Microphone",
 			"Headphone", "Headphone Jack",
 			"Speaker", "Builtin Speaker";
 		simple-audio-card,routing =
-			"MIC_IN", "Microphone Jack",
-			"Microphone Jack", "Mic Bias",
+			"MIC_IN", "Mic Mux OUT",
+			"Mic Mux IN1", "Headset Microphone",
+			"Mic Mux IN2", "Builtin Microphone",
+			"Mic Mux OUT", "Mic Bias",
 			"Headphone Jack", "HP_OUT",
 			"Builtin Speaker", "Speaker Amp OUTR",
 			"Speaker Amp INR", "LINE_OUT";
@@ -650,6 +661,12 @@ MX8MQ_IOMUXC_SAI5_RXFS_GPIO3_IO19	0x8  /* IMU_INT */
 		>;
 	};
 
+	pinctrl_micsel: micselgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5	0xc6  /* MIC_SEL */
+		>;
+	};
+
 	pinctrl_spkamp: spkamp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SPDIF_TX_GPIO5_IO3		0x81  /* MUTE */
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v1 0/6] arm64: dts: librem5-devkit: Improve audio support

From: Shawn Guo <shawnguo@kernel.org>
Date: 2021-03-07 13:47:05 

On Sun, Feb 21, 2021 at 12:07:05PM +0100, Guido Günther wrote:
So far only headphone output worked. Thesse patches add support for the
built in speaker and mic, allow a headset microphone to work and wire up jack
detection so audio output can switch to headphones automatically.  They also
adjust the card name to match the board not the codec, similar what's done for
the Librem 5.

Patches are against next-20210210 but also apply against Shawn's imx-dt64-5.12

Guido Günther (6):
  arm64: dts: librem5-devkit: Use a less generic codec name
  arm64: dts: librem5-devkit: Add speaker amplifier
  arm64: dts: librem5-devkit: "Drop Line In Jack"
  arm64: defconfig: Enable asoc simple mux
  arm64: dts: librem5-devkit: Add mux for built-in vs headset mic
  arm64: dts: librem5-devkit: Move headphone detection to sound card
Applied all, thanks.

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help