Hi Nicolas,

On Thu, Jun 04, 2020 at 07:26:07PM +0200, Nicolas Saenz Julienne wrote:

On Wed, 2020-05-27 at 17:47 +0200, Maxime Ripard wrote:

quoted

The HDMI block has a block that controls clocks and reset signals to the
HDMI0 and HDMI1 controllers.

Why not having two separate drivers?

They share the same address space, so it wouldn't really make sense to
split it into two drivers and an MFD, especially when the clock/reset
association is fairly common.

quoted

Let's expose that through a clock driver implementing a clock and reset
provider.

Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Maxime Ripard <redacted>
---
 drivers/clk/bcm/Kconfig           |  11 +++-
 drivers/clk/bcm/Makefile          |   1 +-
 drivers/clk/bcm/clk-bcm2711-dvp.c | 127 +++++++++++++++++++++++++++++++-
 3 files changed, 139 insertions(+)
 create mode 100644 drivers/clk/bcm/clk-bcm2711-dvp.c

diff --git a/drivers/clk/bcm/Kconfig b/drivers/clk/bcm/Kconfig
index 8c83977a7dc4..784f12c72365 100644
--- a/drivers/clk/bcm/Kconfig
+++ b/drivers/clk/bcm/Kconfig

@@ -1,4 +1,15 @@
 # SPDX-License-Identifier: GPL-2.0-only
+
+config CLK_BCM2711_DVP
+	tristate "Broadcom BCM2711 DVP support"
+	depends on ARCH_BCM2835 ||COMPILE_TEST
+	depends on COMMON_CLK
+	default ARCH_BCM2835
+	select RESET_SIMPLE
+	help
+	  Enable common clock framework support for the Broadcom BCM2711
+	  DVP Controller.
+
 config CLK_BCM2835
 	bool "Broadcom BCM2835 clock support"
 	depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST

diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
index 0070ddf6cdd2..2c1349062147 100644
--- a/drivers/clk/bcm/Makefile
+++ b/drivers/clk/bcm/Makefile

@@ -6,6 +6,7 @@ obj-$(CONFIG_CLK_BCM_KONA)	+= clk-kona-setup.o
 obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm281xx.o
 obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm21664.o
 obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-iproc-armpll.o clk-iproc-pll.o

clk-iproc-asiu.o
+obj-$(CONFIG_CLK_BCM2835)	+= clk-bcm2711-dvp.o
 obj-$(CONFIG_CLK_BCM2835)	+= clk-bcm2835.o
 obj-$(CONFIG_CLK_BCM2835)	+= clk-bcm2835-aux.o
 obj-$(CONFIG_CLK_RASPBERRYPI)	+= clk-raspberrypi.o

diff --git a/drivers/clk/bcm/clk-bcm2711-dvp.c b/drivers/clk/bcm/clk-bcm2711-

dvp.c
new file mode 100644
index 000000000000..c1c4b5857d32

--- /dev/null
+++ b/drivers/clk/bcm/clk-bcm2711-dvp.c

@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2020 Cerno
+
+#include <linux/clk-provider.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/reset-controller.h>
+#include <linux/reset/reset-simple.h>
+
+#define DVP_HT_RPI_SW_INIT	0x04
+#define DVP_HT_RPI_MISC_CONFIG	0x08
+
+#define NR_CLOCKS	2
+#define NR_RESETS	6
+
+struct clk_dvp {
+	struct clk_hw_onecell_data	*data;
+	struct reset_simple_data	reset;
+};
+
+static const struct clk_parent_data clk_dvp_parent = {
+	.index	= 0,
+};
+
+static int clk_dvp_probe(struct platform_device *pdev)
+{
+	struct clk_hw_onecell_data *data;
+	struct resource *res;
+	struct clk_dvp *dvp;
+	void __iomem *base;
+	int ret;
+
+	dvp = devm_kzalloc(&pdev->dev, sizeof(*dvp), GFP_KERNEL);
+	if (!dvp)
+		return -ENOMEM;
+	platform_set_drvdata(pdev, dvp);
+
+	dvp->data = devm_kzalloc(&pdev->dev,
+				 struct_size(dvp->data, hws, NR_CLOCKS),
+				 GFP_KERNEL);
+	if (!dvp->data)
+		return -ENOMEM;
+	data = dvp->data;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	base = devm_ioremap_resource(&pdev->dev, res);

I think the cool function to use these days is
devm_platform_get_and_ioremap_resource().

i'll change it, thanks!
Maxime