[PATCH V2 1/6] ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1

@@ -162,6 +162,40 @@ pins1 {
 		};
 	};
 
+	ethernet0_rmii_pins_a: rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF0)>,   /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
 	fmc_pins_a: fmc-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */

@@ -719,6 +719,26 @@ pins {
 		};
 	};
 
+
+	sai2a_pins_b: sai2a-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 6, AF10)>,	/* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, AF10)>,	/* SAI2_FS_A */
+				 <STM32_PINMUX('D', 13, AF10)>;	/* SAI2_SCK_A */
+			slew-rate = <0>;
+			drive-push-pull;
+			bias-disable;
+		};
+	};
+
+	sai2a_sleep_pins_b: sai2a-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('I', 6, ANALOG)>,  /* SAI2_SD_A */
+				 <STM32_PINMUX('I', 7, ANALOG)>,  /* SAI2_FS_A */
+				 <STM32_PINMUX('D', 13, ANALOG)>; /* SAI2_SCK_A */
+		};
+	};
+
 	sai2b_pins_a: sai2b-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */

@@ -1107,6 +1107,19 @@ pins2 {
 			bias-disable;
 		};
 	};
+
+	uart8_pins_a: uart8-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('E', 0, AF8)>; /* UART8_RX */
+			bias-disable;
+		};
+	};
 };
 
 &pinctrl_z {

@@ -1369,10 +1369,12 @@ ethernet0: ethernet@5800a000 {
 			clock-names = "stmmaceth",
 				      "mac-clk-tx",
 				      "mac-clk-rx",
+				      "eth-ck",
 				      "ethstp";
 			clocks = <&rcc ETHMAC>,
 				 <&rcc ETHTX>,
 				 <&rcc ETHRX>,
+				 <&rcc ETHCK_K>,
 				 <&rcc ETHSTP>;
 			st,syscon = <&syscfg 0x4>;
 			snps,mixed-burst;

@@ -1054,6 +1054,19 @@ pins {
 		};
 	};
 
+	usart3_pins_a: usart3-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
 	uart4_pins_a: uart4-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */

@@ -1019,6 +1019,7 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32h743i-disco.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dk1.dtb \
+	stm32mp157c-dhcom-pdk2.dtb \
 	stm32mp157c-dk2.dtb \
 	stm32mp157c-ed1.dtb \
 	stm32mp157c-ev1.dtb

@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+
+#include "stm32mp157c-dhcom-som.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "STMicroelectronics STM32MP157C DHCOM Premium Developer Kit (2)";
+	compatible = "dh,stm32mp157c-dhcom-pdk2", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+		serial1 = &usart3;
+		serial2 = &uart8;
+		ethernet0 = &ethernet0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clk_ext_audio_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	display_bl: display-bl {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 16 22 30 40 55 75 102 138 188 255>;
+		default-brightness-level = <8>;
+		enable-gpios = <&gpioi 0 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpiog 3 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	panel {
+		compatible = "edt,etm0700g0edh6";
+		backlight = <&display_bl>;
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "audio-graph-card";
+		routing =
+			"MIC_IN", "Capture",
+			"Capture", "Mic Bias",
+			"Playback", "HP_OUT";
+		dais = <&sai2a_port &sai2b_port>;
+		status = "okay";
+	};
+};
+
+&cec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&cec_pins_a>;
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_pins_sleep_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth-ref-clk-sel;
+	phy-reset-gpios = <&gpioh 15 GPIO_ACTIVE_LOW>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@1 {
+			reg = <1>;
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_ext_audio_codec>;
+		VDDA-supply = <&v3v3>;
+		VDDIO-supply = <&vdd>;
+
+		sgtl5000_port: port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sgtl5000_tx_endpoint: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&sai2a_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+
+			sgtl5000_rx_endpoint: endpoint@1 {
+				reg = <1>;
+				remote-endpoint = <&sai2b_endpoint>;
+				frame-master;
+				bitclock-master;
+			};
+		};
+
+	};
+
+	polytouch@38 {
+		compatible = "edt,edt-ft5x06";
+		reg = <0x38>;
+		interrupt-parent = <&gpiog>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		linux,wakeup;
+	};
+};
+
+&ltdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ltdc_pins_b>;
+	pinctrl-1 = <&ltdc_pins_sleep_b>;
+	status = "okay";
+
+	port {
+		lcd_display_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_a>;
+	pinctrl-1 = <&m_can1_sleep_pins_a>;
+	status = "okay";
+};
+
+&sai2 {
+	clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>;
+	clock-names = "pclk", "x8k", "x11k";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sai2a_pins_b &sai2b_pins_b>;
+	pinctrl-1 = <&sai2a_sleep_pins_b &sai2b_sleep_pins_b>;
+	status = "okay";
+
+	sai2a: audio-controller@4400b004 {
+		#clock-cells = <0>;
+		dma-names = "tx";
+		clocks = <&rcc SAI2_K>;
+		clock-names = "sai_ck";
+		status = "okay";
+
+		sai2a_port: port {
+			sai2a_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_tx_endpoint>;
+				format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+
+	sai2b: audio-controller@4400b024 {
+		dma-names = "rx";
+		st,sync = <&sai2a 2>;
+		clocks = <&rcc SAI2_K>, <&sai2a>;
+		clock-names = "sai_ck", "MCLK";
+		status = "okay";
+
+		sai2b_port: port {
+			sai2b_endpoint: endpoint {
+				remote-endpoint = <&sgtl5000_rx_endpoint>;
+				format = "i2s";
+				mclk-fs = <512>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <16>;
+			};
+		};
+	};
+};
+
+&timers2 {
+	/* spare dmas for other usage (un-delete to enable pwm capture) */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+	pwm2: pwm {
+		pinctrl-0 = <&pwm2_pins_a>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+	timer@1 {
+		status = "okay";
+	};
+};
+
+&usart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usart3_pins_a>;
+	status = "okay";
+};
+
+&uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+	vdda1v1-supply = <&reg11>;
+	vdda1v8-supply = <&reg18>;
+};

@@ -0,0 +1,368 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) 2019 Marek Vasut <marex@denx.de>
+ */
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xC0000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
+};
+
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,min-sample-time-nsecs = <5000>;
+		st,adc-channels = <0>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <1>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+			ldo1-supply = <&v3v3>;
+			ldo2-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo5-supply = <&v3v3>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			vdda: ldo1 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v2v8: ldo2 {
+				regulator-name = "v2v8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-boot-on;
+			};
+
+			v1v8: ldo6 {
+				regulator-name = "v1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				interrupts = <IT_CURLIM_LDO6 0>;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+			};
+
+			vbus_sw: pwr_sw2 {
+				regulator-name = "vbus_sw";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-active-discharge;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			power-off-time-sec = <10>;
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+
+	touchscreen@49 {
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		vio-supply = <&v3v3>;
+		interrupts-extended = <&gpioh 3 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: mx66l51235l@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <108000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
+	broken-cd;
+	st,sig-dir;
+	st,neg-edge;
+	st,use-ckin;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	mmc-ddr-3_3v;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_a>;
+	status = "okay";
+};