[GIT PULL] Second Round of Renesas ARM64 Based SoC DT Updates for v4.13

13 messages, 2 authors, 2017-06-19 · open the first message on its own page

[GIT PULL] Second Round of Renesas ARM64 Based SoC DT Updates for v4.13

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:17

Hi Olof, Hi Kevin, Hi Arnd,

Please consider these second round of Renesas ARM64 based SoC DT updates
for v4.13.

This pull request is based on the previous round of
such requests, tagged as renesas-arm64-dt-for-v4.13,
which you have already pulled.


The following changes since commit 0b03c32db03d63de695c1e0ab1950eb12b135fa7:

  arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0 (2017-05-22 14:54:57 +0200)

are available in the git repository at:

  https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt2-for-v4.13

for you to fetch changes up to 4d1255ebefb6838eab4f652107433438bea0051f:

  arm64: dts: r8a7796: Add reset control properties for audio (2017-06-14 11:00:29 +0200)

----------------------------------------------------------------
Second Round of Renesas ARM64 Based SoC DT Updates for v4.13

* Add reset control properties for audio to r9a779[56] SoCs
* Add add DMA for IIC_DVFS to r9a779[56] SoCs
* Add support for Salvator-XS and H3ULCB with R-Car H3 (r8a7795) ES2
* Add missing index to PWM pinctrl subnode name to Salvator-X board
* Add 12288000 for sound ADG to Salvator-X and ULCB boards

----------------------------------------------------------------
Geert Uytterhoeven (7):
      arm64: dts: r8a7795: h3ulcb: Add support for R-Car H3 ES2.0
      arm64: dts: salvator-x: Add missing index to PWM pinctrl subnode name
      arm64: dts: renesas: Extract common Salvator-X/XS board support
      arm64: dts: renesas: Add common Salvator-XS board support
      arm64: dts: renesas: Add support for Salvator-XS with R-Car H3 ES2.0
      arm64: dts: r8a7795: Add reset control properties for audio
      arm64: dts: r8a7796: Add reset control properties for audio

Kuninori Morimoto (2):
      arm64: dts: salvator-x: add 12288000 for sound ADG
      arm64: dts: ulcb: add 12288000 for sound ADG

Wolfram Sang (2):
      arm64: dts: r8a7795: add DMA for IIC_DVFS
      arm64: dts: r8a7796: add DMA for IIC_DVFS

 arch/arm64/boot/dts/renesas/Makefile               |   3 +-
 arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts |  42 ++
 arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts     |   4 +-
 .../arm64/boot/dts/renesas/r8a7795-salvator-xs.dts | 109 ++++
 arch/arm64/boot/dts/renesas/r8a7795.dtsi           |  12 +
 arch/arm64/boot/dts/renesas/r8a7796.dtsi           |  12 +
 arch/arm64/boot/dts/renesas/salvator-common.dtsi   | 629 +++++++++++++++++++++
 arch/arm64/boot/dts/renesas/salvator-x.dtsi        | 616 +-------------------
 arch/arm64/boot/dts/renesas/salvator-xs.dtsi       |  20 +
 arch/arm64/boot/dts/renesas/ulcb.dtsi              |   2 +-
 10 files changed, 830 insertions(+), 619 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-common.dtsi
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-xs.dtsi

[PATCH 01/11] arm64: dts: salvator-x: add 12288000 for sound ADG

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:09

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/salvator-x.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 5f0d4bdcd3b4..937bdf8842f2 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -523,7 +523,7 @@
 
 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
-	clock-frequency = <11289600>;
+	clock-frequency = <11289600 12288000>;
 
 	status = "okay";
 
-- 
2.1.4

[PATCH 02/11] arm64: dts: ulcb: add 12288000 for sound ADG

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:10

From: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>

Current rcar_sound only has 11289600 (= for 44.1kHz) clock-frequency,
but it needs 12288000 for 48kHz too.
Otherwise, 48kHz based sound can't handle correctly.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/ulcb.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi
index 41e83c8530f7..b5c6ee07d7f9 100644
--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi
@@ -281,7 +281,7 @@
 
 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
-	clock-frequency = <11289600>;
+	clock-frequency = <11289600 12288000>;
 
 	status = "okay";
 
-- 
2.1.4

[PATCH 03/11] arm64: dts: r8a7795: add DMA for IIC_DVFS

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:11

From: Wolfram Sang <wsa+renesas@sang-engineering.com>

Tested with a Salvator-X.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 2 ++
 1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index 24c607e30009..a4ca0f5bb762 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -883,6 +883,8 @@
 			clocks = <&cpg CPG_MOD 926>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 926>;
+			dmas = <&dmac0 0x11>, <&dmac0 0x10>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-- 
2.1.4

[PATCH 04/11] arm64: dts: r8a7796: add DMA for IIC_DVFS

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:12

From: Wolfram Sang <wsa+renesas@sang-engineering.com>

Tested with a Salvator-X.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 2 ++
 1 file changed, 2 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index b418a66f4cec..d63acd3e00b2 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -392,6 +392,8 @@
 			clocks = <&cpg CPG_MOD 926>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 926>;
+			dmas = <&dmac0 0x11>, <&dmac0 0x10>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-- 
2.1.4

[PATCH 05/11] arm64: dts: r8a7795: h3ulcb: Add support for R-Car H3 ES2.0

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:13

From: Geert Uytterhoeven <geert+renesas@glider.be>

Split off support for H3ULCB boards with the ES1.x revision of the R-Car
H3 SoC into a separate file.  The main r8a7795-h3ulcb.dts file now
corresponds to H3ULCB with R-Car H3 ES2.0 or later.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/Makefile               |  2 +-
 arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts | 42 ++++++++++++++++++++++
 arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts     |  4 +--
 3 files changed, 45 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index b6c723d8f687..d5451015950e 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -1,5 +1,5 @@
 dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
-dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-salvator-x.dtb
+dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-salvator-x.dtb r8a7795-es1-h3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 
 always		:= $(dtb-y)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts
new file mode 100644
index 000000000000..95fe207cb6a3
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a7795-es1-h3ulcb.dts
@@ -0,0 +1,42 @@
+/*
+ * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) board
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
+
+/dts-v1/;
+#include "r8a7795-es1.dtsi"
+#include "ulcb.dtsi"
+
+/ {
+	model = "Renesas H3ULCB board based on r8a7795 ES1.x";
+	compatible = "renesas,h3ulcb", "renesas,r8a7795";
+
+	memory at 48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	memory at 500000000 {
+		device_type = "memory";
+		reg = <0x5 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 700000000 {
+		device_type = "memory";
+		reg = <0x7 0x00000000 0x0 0x40000000>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index 95fe207cb6a3..0426f41765f0 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -12,11 +12,11 @@
 #define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
 
 /dts-v1/;
-#include "r8a7795-es1.dtsi"
+#include "r8a7795.dtsi"
 #include "ulcb.dtsi"
 
 / {
-	model = "Renesas H3ULCB board based on r8a7795 ES1.x";
+	model = "Renesas H3ULCB board based on r8a7795 ES2.0+";
 	compatible = "renesas,h3ulcb", "renesas,r8a7795";
 
 	memory at 48000000 {
-- 
2.1.4

[PATCH 06/11] arm64: dts: salvator-x: Add missing index to PWM pinctrl subnode name

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:14

From: Geert Uytterhoeven <geert+renesas@glider.be>

R-Car Gen3 SoCs contain multiple PWM modules.  Hence to avoid conflicts,
pinctrl subnodes for PWM should include indices referring to their
instances.

Fixes: b33be33670217533 ("arm64: dts: salvator-x: Add panel backlight support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/salvator-x.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 937bdf8842f2..2f5386252aed 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -417,7 +417,7 @@
 		function = "i2c2";
 	};
 
-	pwm1_pins: pwm {
+	pwm1_pins: pwm1 {
 		groups = "pwm1_a";
 		function = "pwm1";
 	};
-- 
2.1.4

[PATCH 07/11] arm64: dts: renesas: Extract common Salvator-X/XS board support

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:15

From: Geert Uytterhoeven <geert+renesas@glider.be>

The Renesas Salvator-X and Salvator-XS (Salvator-X 2nd version) boards
are very similar.  To avoid duplication, prepare for the advent of the
latter by extracting the common board parts into its own .dtsi file.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/salvator-common.dtsi | 629 +++++++++++++++++++++++
 arch/arm64/boot/dts/renesas/salvator-x.dtsi      | 616 +---------------------
 2 files changed, 630 insertions(+), 615 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-common.dtsi
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
new file mode 100644
index 000000000000..aef35e0b685a
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -0,0 +1,629 @@
+/*
+ * Device Tree Source for common parts of Salvator-X board variants
+ *
+ * Copyright (C) 2015-2016 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/*
+ * SSI-AK4613
+ *
+ * This command is required when Playback/Capture
+ *
+ *	amixer set "DVC Out" 100%
+ *	amixer set "DVC In" 100%
+ *
+ * You can use Mute
+ *
+ *	amixer set "DVC Out Mute" on
+ *	amixer set "DVC In Mute" on
+ *
+ * You can use Volume Ramp
+ *
+ *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
+ *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
+ *	amixer set "DVC Out Ramp" on
+ *	aplay xxx.wav &
+ *	amixer set "DVC Out"  80%  // Volume Down
+ *	amixer set "DVC Out" 100%  // Volume Up
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		serial0 = &scif2;
+		serial1 = &scif1;
+		ethernet0 = &avb;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_clkout: audio_clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000>;
+
+		brightness-levels = <256 128 64 16 8 4 0>;
+		default-brightness-level = <6>;
+
+		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rsnd_ak4613: sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcpu>;
+		simple-audio-card,frame-master = <&sndcpu>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4613>;
+		};
+	};
+
+	vbus0_usb2: regulator-vbus0-usb2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB20_VBUS0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	vcc_sdhi3: regulator-vcc-sdhi3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI3 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi3: regulator-vccq-sdhi3 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI3 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	hdmi0-out {
+		compatible = "hdmi-connector";
+		label = "HDMI0 OUT";
+		type = "a";
+
+		port {
+			hdmi0_con: endpoint {
+			};
+		};
+	};
+
+	hdmi1-out {
+		compatible = "hdmi-connector";
+		label = "HDMI1 OUT";
+		type = "a";
+
+		port {
+			hdmi1_con: endpoint {
+			};
+		};
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port at 1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	/* External DU dot clocks */
+	x21_clk: x21-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33000000>;
+	};
+
+	x22_clk: x22-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33000000>;
+	};
+
+	x23_clk: x23-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+};
+
+&audio_clk_a {
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy at 0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ports {
+		port at 0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+		port at 3 {
+			lvds_connector: endpoint {
+			};
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&hsusb {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	ak4613: codec at 10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 3>;
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+	};
+
+	cs2000: clk_multiplier at 4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x12_clk>;
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	csa_vdd: adc at 7c {
+		compatible = "maxim,max9611";
+		reg = <0x7c>;
+
+		shunt-resistor-micro-ohms = <5000>;
+	};
+
+	csa_dvfs: adc at 7f {
+		compatible = "maxim,max9611";
+		reg = <0x7f>;
+
+		shunt-resistor-micro-ohms = <5000>;
+	};
+};
+
+&i2c_dvfs {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pciec0 {
+	status = "okay";
+};
+
+&pciec1 {
+	status = "okay";
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	avb_pins: avb {
+		mux {
+			groups = "avb_link", "avb_phy_int", "avb_mdc",
+				 "avb_mii";
+			function = "avb";
+		};
+
+		pins_mdc {
+			groups = "avb_mdc";
+			drive-strength = <24>;
+		};
+
+		pins_mii_tx {
+			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
+			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
+			drive-strength = <12>;
+		};
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
+		function = "du";
+	};
+
+	i2c2_pins: i2c2 {
+		groups = "i2c2_a";
+		function = "i2c2";
+	};
+
+	pwm1_pins: pwm1 {
+		groups = "pwm1_a";
+		function = "pwm1";
+	};
+
+	scif1_pins: scif1 {
+		groups = "scif1_data_a", "scif1_ctrl";
+		function = "scif1";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk_a";
+		function = "scif_clk";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
+	};
+
+	sdhi3_pins: sd3 {
+		groups = "sdhi3_data4", "sdhi3_ctrl";
+		function = "sdhi3";
+		power-source = <3300>;
+	};
+
+	sdhi3_pins_uhs: sd3_uhs {
+		groups = "sdhi3_data4", "sdhi3_ctrl";
+		function = "sdhi3";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound_clk {
+		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
+			 "audio_clkout_a", "audio_clkout3_a";
+		function = "audio_clk";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		mux {
+			groups = "usb1";
+			function = "usb1";
+		};
+
+		ovc {
+			pins = "GP_6_27";
+			bias-pull-up;
+		};
+
+		pwen {
+			pins = "GP_6_26";
+			bias-pull-down;
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-0 = <&pwm1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1/2/3 */
+	#clock-cells = <1>;
+	clock-frequency = <11289600 12288000>;
+
+	status = "okay";
+
+	/* update <audio_clk_b> to <cs2000> */
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&audio_clk_a>, <&cs2000>,
+		 <&audio_clk_c>,
+		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi0 &src0 &dvc0>;
+			capture  = <&ssi1 &src1 &dvc1>;
+		};
+	};
+};
+
+&scif1 {
+	pinctrl-0 = <&scif1_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&scif_clk {
+	clock-frequency = <14745600>;
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&sdhi2 {
+	/* used for on-board 8bit eMMC */
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&sdhi3 {
+	pinctrl-0 = <&sdhi3_pins>;
+	pinctrl-1 = <&sdhi3_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi3>;
+	vqmmc-supply = <&vccq_sdhi3>;
+	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&wdt0 {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&xhci0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 2f5386252aed..468868c8ed9f 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -8,335 +8,18 @@
  * kind, whether express or implied.
  */
 
-/*
- * SSI-AK4613
- *
- * This command is required when Playback/Capture
- *
- *	amixer set "DVC Out" 100%
- *	amixer set "DVC In" 100%
- *
- * You can use Mute
- *
- *	amixer set "DVC Out Mute" on
- *	amixer set "DVC In Mute" on
- *
- * You can use Volume Ramp
- *
- *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
- *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
- *	amixer set "DVC Out Ramp" on
- *	aplay xxx.wav &
- *	amixer set "DVC Out"  80%  // Volume Down
- *	amixer set "DVC Out" 100%  // Volume Up
- */
-
-#include <dt-bindings/gpio/gpio.h>
+#include "salvator-common.dtsi"
 
 / {
 	model = "Renesas Salvator-X board";
 	compatible = "renesas,salvator-x";
-
-	aliases {
-		serial0 = &scif2;
-		serial1 = &scif1;
-		ethernet0 = &avb;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_clkout: audio_clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
-
-		brightness-levels = <256 128 64 16 8 4 0>;
-		default-brightness-level = <6>;
-
-		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	rsnd_ak4613: sound {
-		compatible = "simple-audio-card";
-
-		simple-audio-card,format = "left_j";
-		simple-audio-card,bitclock-master = <&sndcpu>;
-		simple-audio-card,frame-master = <&sndcpu>;
-
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&ak4613>;
-		};
-	};
-
-	vbus0_usb2: regulator-vbus0-usb2 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	vcc_sdhi3: regulator-vcc-sdhi3 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI3 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi3: regulator-vccq-sdhi3 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI3 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	hdmi0-out {
-		compatible = "hdmi-connector";
-		label = "HDMI0 OUT";
-		type = "a";
-
-		port {
-			hdmi0_con: endpoint {
-			};
-		};
-	};
-
-	hdmi1-out {
-		compatible = "hdmi-connector";
-		label = "HDMI1 OUT";
-		type = "a";
-
-		port {
-			hdmi1_con: endpoint {
-			};
-		};
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port at 0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port at 1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	/* External DU dot clocks */
-	x21_clk: x21-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <33000000>;
-	};
-
-	x22_clk: x22-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <33000000>;
-	};
-
-	x23_clk: x23-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-	};
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy at 0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	ports {
-		port at 0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-		port at 3 {
-			lvds_connector: endpoint {
-			};
-		};
-	};
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
 };
 
 &extal_clk {
 	clock-frequency = <16666666>;
 };
 
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&hsusb {
-	status = "okay";
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ak4613: codec at 10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk_multiplier at 4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
 &i2c4 {
-	status = "okay";
-
 	versaclock5: clock-generator at 6a {
 		compatible = "idt,5p49v5923";
 		reg = <0x6a>;
@@ -344,301 +27,4 @@
 		clocks = <&x23_clk>;
 		clock-names = "xin";
 	};
-
-	csa_vdd: adc at 7c {
-		compatible = "maxim,max9611";
-		reg = <0x7c>;
-
-		shunt-resistor-micro-ohms = <5000>;
-	};
-
-	csa_dvfs: adc at 7f {
-		compatible = "maxim,max9611";
-		reg = <0x7f>;
-
-		shunt-resistor-micro-ohms = <5000>;
-	};
-};
-
-&i2c_dvfs {
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pciec0 {
-	status = "okay";
-};
-
-&pciec1 {
-	status = "okay";
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	avb_pins: avb {
-		mux {
-			groups = "avb_link", "avb_phy_int", "avb_mdc",
-				 "avb_mii";
-			function = "avb";
-		};
-
-		pins_mdc {
-			groups = "avb_mdc";
-			drive-strength = <24>;
-		};
-
-		pins_mii_tx {
-			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
-			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
-			drive-strength = <12>;
-		};
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
-		function = "du";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	pwm1_pins: pwm1 {
-		groups = "pwm1_a";
-		function = "pwm1";
-	};
-
-	scif1_pins: scif1 {
-		groups = "scif1_data_a", "scif1_ctrl";
-		function = "scif1";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <3300>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <3300>;
-	};
-
-	sdhi3_pins_uhs: sd3_uhs {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound_clk {
-		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout3_a";
-		function = "audio_clk";
-	};
-
-	usb0_pins: usb0 {
-		groups = "usb0";
-		function = "usb0";
-	};
-
-	usb1_pins: usb1 {
-		mux {
-			groups = "usb1";
-			function = "usb1";
-		};
-
-		ovc {
-			pins = "GP_6_27";
-			bias-pull-up;
-		};
-
-		pwen {
-			pins = "GP_6_26";
-			bias-pull-down;
-		};
-	};
-};
-
-&pwm1 {
-	pinctrl-0 = <&pwm1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <11289600 12288000>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
-		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
-
-	rcar_sound,dai {
-		dai0 {
-			playback = <&ssi0 &src0 &dvc0>;
-			capture  = <&ssi1 &src1 &dvc1>;
-		};
-	};
-};
-
-&scif1 {
-	pinctrl-0 = <&scif1_pins>;
-	pinctrl-names = "default";
-
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	non-removable;
-	status = "okay";
-};
-
-&sdhi3 {
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi3>;
-	vqmmc-supply = <&vccq_sdhi3>;
-	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
-	status = "okay";
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&wdt0 {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&xhci0 {
-	status = "okay";
 };
-- 
2.1.4

[PATCH 08/11] arm64: dts: renesas: Add common Salvator-XS board support

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:16

From: Geert Uytterhoeven <geert+renesas@glider.be>

The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.

Add initial support for the common parts of the Salvator-XS board into
its own .dtsi file, to be included by the DTSes for the H3/M3-W
versions.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/salvator-xs.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-xs.dtsi
diff --git a/arch/arm64/boot/dts/renesas/salvator-xs.dtsi b/arch/arm64/boot/dts/renesas/salvator-xs.dtsi
new file mode 100644
index 000000000000..81227e3c2c6f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/salvator-xs.dtsi
@@ -0,0 +1,20 @@
+/*
+ * Device Tree Source for the Salvator-X 2nd version board
+ *
+ * Copyright (C) 2015-2017 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include "salvator-common.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board";
+	compatible = "renesas,salvator-xs";
+};
+
+&extal_clk {
+	clock-frequency = <16640000>;
+};
-- 
2.1.4

[PATCH 09/11] arm64: dts: renesas: Add support for Salvator-XS with R-Car H3 ES2.0

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:17

From: Geert Uytterhoeven <geert+renesas@glider.be>

Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car H3 ES2.0 SiP.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/Makefile               |   1 +
 .../arm64/boot/dts/renesas/r8a7795-salvator-xs.dts | 109 +++++++++++++++++++++
 2 files changed, 110 insertions(+)
 create mode 100644 arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index d5451015950e..acc4bb30d485 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -1,4 +1,5 @@
 dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
+dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-es1-salvator-x.dtb r8a7795-es1-h3ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
 
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
new file mode 100644
index 000000000000..de354957144b
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dts
@@ -0,0 +1,109 @@
+/*
+ * Device Tree Source for the Salvator-X 2nd version board
+ *
+ * Copyright (C) 2015-2017 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#define CPG_AUDIO_CLK_I		R8A7795_CLK_S0D4
+
+/dts-v1/;
+#include "r8a7795.dtsi"
+#include "salvator-xs.dtsi"
+
+/ {
+	model = "Renesas Salvator-X 2nd version board based on r8a7795 ES2.0+";
+	compatible = "renesas,salvator-xs", "renesas,r8a7795";
+
+	memory at 48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	memory at 500000000 {
+		device_type = "memory";
+		reg = <0x5 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x0 0x40000000>;
+	};
+
+	memory at 700000000 {
+		device_type = "memory";
+		reg = <0x7 0x00000000 0x0 0x40000000>;
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&cpg CPG_MOD 723>,
+		 <&cpg CPG_MOD 722>,
+		 <&cpg CPG_MOD 721>,
+		 <&cpg CPG_MOD 727>,
+		 <&x21_clk>,
+		 <&x22_clk>;
+	clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0",
+		      "dclkin.1", "dclkin.2";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&hdmi0 {
+	status = "okay";
+
+	ports {
+		port at 1 {
+			reg = <1>;
+			rcar_dw_hdmi0_out: endpoint {
+				remote-endpoint = <&hdmi0_con>;
+			};
+		};
+	};
+};
+
+&hdmi0_con {
+	remote-endpoint = <&rcar_dw_hdmi0_out>;
+};
+
+&hdmi1 {
+	status = "okay";
+
+	ports {
+		port at 1 {
+			reg = <1>;
+			rcar_dw_hdmi1_out: endpoint {
+				remote-endpoint = <&hdmi1_con>;
+			};
+		};
+	};
+};
+
+&hdmi1_con {
+	remote-endpoint = <&rcar_dw_hdmi1_out>;
+};
+
+&ohci2 {
+	status = "okay";
+};
+
+&pfc {
+	usb2_pins: usb2 {
+		groups = "usb2";
+		function = "usb2";
+	};
+};
+
+&usb2_phy2 {
+	pinctrl-0 = <&usb2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
-- 
2.1.4

[PATCH 10/11] arm64: dts: r8a7795: Add reset control properties for audio

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:18

From: Geert Uytterhoeven <geert+renesas@glider.be>

Note that the audio module has resets for the Serial Sound Interfaces
only.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index a4ca0f5bb762..e31c1b660b3f 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -1120,6 +1120,16 @@
 				      "dvc.0", "dvc.1",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 1005>,
+				 <&cpg 1006>, <&cpg 1007>,
+				 <&cpg 1008>, <&cpg 1009>,
+				 <&cpg 1010>, <&cpg 1011>,
+				 <&cpg 1012>, <&cpg 1013>,
+				 <&cpg 1014>, <&cpg 1015>;
+			reset-names = "ssi-all",
+				      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+				      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+				      "ssi.1", "ssi.0";
 			status = "disabled";
 
 			rcar_sound,dvc {
-- 
2.1.4

[PATCH 11/11] arm64: dts: r8a7796: Add reset control properties for audio

From: Simon Horman <hidden>
Date: 2017-06-16 13:30:19

From: Geert Uytterhoeven <geert+renesas@glider.be>

Note that the audio module has resets for the Serial Sound Interfaces
only.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <redacted>
---
 arch/arm64/boot/dts/renesas/r8a7796.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index d63acd3e00b2..1f6710912045 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -1286,6 +1286,16 @@
 				      "dvc.0", "dvc.1",
 				      "clk_a", "clk_b", "clk_c", "clk_i";
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 1005>,
+				 <&cpg 1006>, <&cpg 1007>,
+				 <&cpg 1008>, <&cpg 1009>,
+				 <&cpg 1010>, <&cpg 1011>,
+				 <&cpg 1012>, <&cpg 1013>,
+				 <&cpg 1014>, <&cpg 1015>;
+			reset-names = "ssi-all",
+				      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+				      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+				      "ssi.1", "ssi.0";
 			status = "disabled";
 
 			rcar_sound,dvc {
-- 
2.1.4

[GIT PULL] Second Round of Renesas ARM64 Based SoC DT Updates for v4.13

From: Olof Johansson <hidden>
Date: 2017-06-19 05:44:20

Hi Simon,

On Fri, Jun 16, 2017 at 03:30:17PM +0200, Simon Horman wrote:
Hi Olof, Hi Kevin, Hi Arnd,

Please consider these second round of Renesas ARM64 based SoC DT updates
for v4.13.

This pull request is based on the previous round of
such requests, tagged as renesas-arm64-dt-for-v4.13,
which you have already pulled.


The following changes since commit 0b03c32db03d63de695c1e0ab1950eb12b135fa7:

  arm64: dts: r8a7795: salvator-x: Add support for R-Car H3 ES2.0 (2017-05-22 14:54:57 +0200)

are available in the git repository at:

  https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt2-for-v4.13

for you to fetch changes up to 4d1255ebefb6838eab4f652107433438bea0051f:

  arm64: dts: r8a7796: Add reset control properties for audio (2017-06-14 11:00:29 +0200)

----------------------------------------------------------------
Second Round of Renesas ARM64 Based SoC DT Updates for v4.13

* Add reset control properties for audio to r9a779[56] SoCs
* Add add DMA for IIC_DVFS to r9a779[56] SoCs
* Add support for Salvator-XS and H3ULCB with R-Car H3 (r8a7795) ES2
* Add missing index to PWM pinctrl subnode name to Salvator-X board
* Add 12288000 for sound ADG to Salvator-X and ULCB boards
This doesn't mean anything to me. Even if I happened to know what ADG is,
I'm not sure what ADG+12288000 is!?

Looking at the patch, it adds a 12288000 clock to the audio block to be able to
play 48k audio. Maybe that's what you meant to say here?

Merged anyway this time.


-Olof
Keyboard shortcuts
hback out one level
jnext message in thread
kprevious message in thread
ldrill in
Escclose help / fold thread tree
?toggle this help