[PATCH 1/4 v5] PCI: add DT bindings for Faraday Technology PCI Host Bridge
From: Linus Walleij <hidden>
Date: 2017-03-12 22:23:52
Also in:
linux-devicetree, linux-pci
Subsystem:
open firmware and flattened device tree bindings, pci native host bridge and endpoint drivers, pci subsystem, the rest · Maintainers:
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Lorenzo Pieralisi, Krzysztof Wilczyński, Manivannan Sadhasivam, Bjorn Helgaas, Linus Torvalds
This adds device tree bindings for the Faraday technology PCI Host Bridge. This IP is found in the Storlink/Storm/Cortina Gemini SoC platform. Cc: Janos Laube <redacted> Cc: Paulius Zaleckas <redacted> Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: devicetree at vger.kernel.org Cc: Feng-Hsin Chiang <redacted> Cc: Greentime Hu <redacted> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <redacted> --- ChangeLog v4->v5: - No changes, just resend as everything else is rebased onto v4.11-rc1. ChangeLog v3->v4: - Add Rob's ACK ChangeLog v2->v3: - Reinstate the specific-to-generic bindings also specifying the "cortina,gemini-pci" fixture for the Faraday block. - Set compatible to "faraday,ftpci100" and "faraday,ftpci100-dual" this is clearly closer to or equal to what the IP blocks from Faraday are actually named. - Add "dma-ranges" property, after deciphering that some hardcoded constants in the driver is really about this. ChangeLog v1->v2: - Rename from Cortina prefixes to Faraday. This is clearly a Faraday IP block. - Support both the version with cascaded interrupts and the "dual" version with 1-to-1 mapped interrupts. - Change bus-range to <0x00 0xff> - Fix spelling mistake - Write a bit about swizzling interrupts on the interrupt controller side - Reasonable swizzling in the interrupt mapping example This can be merged to the PCI tree whenever it is considered fine for inclusion. --- .../devicetree/bindings/pci/faraday,ftpci100.txt | 129 +++++++++++++++++++++ 1 file changed, 129 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt
new file mode 100644
index 000000000000..35d4a979bb7b
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt@@ -0,0 +1,129 @@ +Faraday Technology FTPCI100 PCI Host Bridge + +This PCI bridge is found inside that Cortina Systems Gemini SoC platform and +is a generic IP block from Faraday Technology. It exists in two variants: +plain and dual PCI. The plain version embeds a cascading interrupt controller +into the host bridge. The dual version routes the interrupts to the host +chips interrupt controller. + +The host controller appear on the PCI bus with vendor ID 0x159b (Faraday +Technology) and product ID 0x4321. + +Mandatory properties: + +- compatible: ranging from specific to generic, should be one of + "cortina,gemini-pci", "faraday,ftpci100" + "cortina,gemini-pci-dual", "faraday,ftpci100-dual" + "faraday,ftpci100" + "faraday,ftpci100-dual" +- reg: memory base and size for the host bridge +- #address-cells: set to <3> +- #size-cells: set to <2> +- #interrupt-cells: set to <1> +- bus-range: set to <0x00 0xff> +- device_type, set to "pci" +- ranges: see pci.txt +- interrupt-map-mask: see pci.txt +- interrupt-map: see pci.txt +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB, + 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as + pre-fetchable. + +Mandatory subnodes: +- For "faraday,ftpci100" a node representing the interrupt-controller inside the + host bridge is mandatory. It has the following mandatory properties: + - interrupt: see interrupt-controller/interrupts.txt + - interrupt-parent: see interrupt-controller/interrupts.txt + - interrupt-controller: see interrupt-controller/interrupts.txt + - #address-cells: set to <0> + - #interrupt-cells: set to <1> + +I/O space considerations: + +The plain variant has 128MiB of non-prefetchable memory space, whereas the +"dual" variant has 64MiB. Take this into account when describing the ranges. + +Interrupt map considerations: + +The "dual" variant will get INT A, B, C, D from the system interrupt controller +and should point to respective interrupt in that controller in its +interrupt-map. + +The code which is the only documentation of how the Faraday PCI (the non-dual +variant) interrupts assigns the default interrupt mapping/swizzling has +typically been like this, doing the swizzling on the interrupt controller side +rather than in the interconnect: + +interrupt-map-mask = <0xf800 0 0 7>; +interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 1>, + <0x6000 0 0 4 &pci_intc 2>; + +Example: + +pci at 50000000 { + compatible = "cortina,gemini-pci", "faraday,ftpci100"; + reg = <0x50000000 0x100>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */ + <26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */ + <27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */ + <28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */ + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + bus-range = <0x00 0xff>; + ranges = /* 1MiB I/O space 0x50000000-0x500fffff */ + <0x01000000 0 0 0x50000000 0 0x00100000>, + /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */ + <0x02000000 0 0x58000000 0x58000000 0 0x08000000>; + + /* DMA ranges */ + dma-ranges = + /* 128MiB at 0x00000000-0x07ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x08000000>, + /* 64MiB at 0x00000000-0x03ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>, + /* 64MiB at 0x00000000-0x03ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>; + + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 0>, + <0x6000 0 0 4 &pci_intc 0>; + pci_intc: interrupt-controller { + interrupt-parent = <&intcon>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; +};
--
2.9.3