[PATCH v2 0/3] ARM: dts: dra7-evm: pinmuxing updates

STALE3566d

Revision v2 of 2 in this series.

5 messages, 2 authors, 2017-01-05 · open the first message on its own page

[PATCH v2 0/3] ARM: dts: dra7-evm: pinmuxing updates

From: Sekhar Nori <hidden>
Date: 2016-12-13 11:29:44

Hi,

This patch series drops most of the pinmuxing from dra7-evm
to satisfy erratum i869 and adds missing eMMC and SD card pinmuxing.

The patches apply to latest linux-next. Tested on DRA74x EVM Rev H
using U-Boot 2016.11. Boot tested using NFS and basic testing carried
out on SD card, eMMC, Audio capture and playback.

NAND on DRA72 EVM is already unusable due to a similar patch. A patch
included here disables the GPMC node.

v1 -> v2:
- Add a patch to disable GPMC node on DRA72x EVM
- Disable GPMC node on DRA74x EVM

Kishon Vijay Abraham I (1):
  ARM: dts: dra7-evm: add pinmux configuration for mmc1/2

Sekhar Nori (2):
  ARM: dts: dra7-evm: Remove pinmux configurations for erratum i869
  ARM: dts: dra72-evm: drop NAND support

 arch/arm/boot/dts/dra7-evm.dts          | 282 ++++----------------------------
 arch/arm/boot/dts/dra72-evm-common.dtsi |   7 +-
 2 files changed, 35 insertions(+), 254 deletions(-)

-- 
2.9.0

[PATCH v2 1/3] ARM: dts: dra7-evm: Remove pinmux configurations for erratum i869

From: Sekhar Nori <hidden>
Date: 2016-12-13 11:29:45

Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.

Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence).

DCAN pinmux is retained in this patch. MMC pinmux is missing from
the dra7-evm.dts file and the board is relying on configuration done
by bootloader. A subsequent patch will add MMC pinmux configuration.

A side-effect of this patch is that NAND support is removed. NAND
pins clash with VOUT3 on DRA7-EVM. U-Boot selects VOUT3 over NAND
as per TI EVM application needs.

[1] http://www.ti.com/lit/pdf/sprz429
[2] http://www.ti.com/lit/pdf/sprui30

Signed-off-by: Sekhar Nori <redacted>
---
 arch/arm/boot/dts/dra7-evm.dts | 267 +----------------------------------------
 1 file changed, 6 insertions(+), 261 deletions(-)

diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 132f2be10889..80ebfd6a5c7b 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts

@@ -151,204 +151,6 @@
 };
 
 &dra7_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&vtt_pin>;
-
-	vtt_pin: pinmux_vtt_pin {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37b4, PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */
-		>;
-	};
-
-	i2c1_pins: pinmux_i2c1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
-			DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
-		>;
-	};
-
-	i2c2_pins: pinmux_i2c2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
-			DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
-		>;
-	};
-
-	i2c3_pins: pinmux_i2c3_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3688, PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */
-			DRA7XX_CORE_IOPAD(0x368c, PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */
-		>;
-	};
-
-	mcspi1_pins: pinmux_mcspi1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37a4, PIN_INPUT | MUX_MODE0) /* spi1_sclk */
-			DRA7XX_CORE_IOPAD(0x37a8, PIN_INPUT | MUX_MODE0) /* spi1_d1 */
-			DRA7XX_CORE_IOPAD(0x37ac, PIN_INPUT | MUX_MODE0) /* spi1_d0 */
-			DRA7XX_CORE_IOPAD(0x37b0, PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
-			DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
-			DRA7XX_CORE_IOPAD(0x37bc, PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
-		>;
-	};
-
-	mcspi2_pins: pinmux_mcspi2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37c0, PIN_INPUT | MUX_MODE0) /* spi2_sclk */
-			DRA7XX_CORE_IOPAD(0x37c4, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
-			DRA7XX_CORE_IOPAD(0x37c8, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_d1 */
-			DRA7XX_CORE_IOPAD(0x37cc, PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
-		>;
-	};
-
-	uart1_pins: pinmux_uart1_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37e0, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_rxd */
-			DRA7XX_CORE_IOPAD(0x37e4, PIN_INPUT_SLEW | MUX_MODE0) /* uart1_txd */
-			DRA7XX_CORE_IOPAD(0x37e8, PIN_INPUT | MUX_MODE3) /* uart1_ctsn */
-			DRA7XX_CORE_IOPAD(0x37ec, PIN_INPUT | MUX_MODE3) /* uart1_rtsn */
-		>;
-	};
-
-	uart2_pins: pinmux_uart2_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x37f0, PIN_INPUT | MUX_MODE0) /* uart2_rxd */
-			DRA7XX_CORE_IOPAD(0x37f4, PIN_INPUT | MUX_MODE0) /* uart2_txd */
-			DRA7XX_CORE_IOPAD(0x37f8, PIN_INPUT | MUX_MODE0) /* uart2_ctsn */
-			DRA7XX_CORE_IOPAD(0x37fc, PIN_INPUT | MUX_MODE0) /* uart2_rtsn */
-		>;
-	};
-
-	uart3_pins: pinmux_uart3_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3648, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd */
-			DRA7XX_CORE_IOPAD(0x364c, PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd */
-		>;
-	};
-
-	usb1_pins: pinmux_usb1_pins {
-                pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
-                >;
-        };
-
-	usb2_pins: pinmux_usb2_pins {
-                pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
-                >;
-        };
-
-	nand_flash_x16: nand_flash_x16 {
-		/* On DRA7 EVM, GPMC_WPN and NAND_BOOTn comes from DIP switch
-		 * So NAND flash requires following switch settings:
-		 * SW5.1 (NAND_BOOTn) = ON (LOW)
-		 * SW5.9 (GPMC_WPN) = OFF (HIGH)
-		 */
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad0	*/
-			DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad1	*/
-			DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad2	*/
-			DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad3	*/
-			DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad4	*/
-			DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad5	*/
-			DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad6	*/
-			DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad7	*/
-			DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad8	*/
-			DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad9	*/
-			DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad10	*/
-			DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad11	*/
-			DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad12	*/
-			DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad13	*/
-			DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad14	*/
-			DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT  | MUX_MODE0)	/* gpmc_ad15	*/
-			DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT_PULLUP  | MUX_MODE0)	/* gpmc_wait0	*/
-			DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0)	/* gpmc_wen	*/
-			DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* gpmc_csn0	*/
-			DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0)	/* gpmc_advn_ale */
-			DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_oen_ren	 */
-			DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0)	/* gpmc_be0n_cle */
-		>;
-	};
-
-	cpsw_default: cpsw_default {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txc.rgmii0_txc */
-			DRA7XX_CORE_IOPAD(0x3654, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txctl.rgmii0_txctl */
-			DRA7XX_CORE_IOPAD(0x3658, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_td3.rgmii0_txd3 */
-			DRA7XX_CORE_IOPAD(0x365c, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd2.rgmii0_txd2 */
-			DRA7XX_CORE_IOPAD(0x3660, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd1.rgmii0_txd1 */
-			DRA7XX_CORE_IOPAD(0x3664, PIN_OUTPUT | MUX_MODE0)	/* rgmii0_txd0.rgmii0_txd0 */
-			DRA7XX_CORE_IOPAD(0x3668, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxc.rgmii0_rxc */
-			DRA7XX_CORE_IOPAD(0x366c, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxctl.rgmii0_rxctl */
-			DRA7XX_CORE_IOPAD(0x3670, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd3.rgmii0_rxd3 */
-			DRA7XX_CORE_IOPAD(0x3674, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd2.rgmii0_rxd2 */
-			DRA7XX_CORE_IOPAD(0x3678, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd1.rgmii0_rxd1 */
-			DRA7XX_CORE_IOPAD(0x367c, PIN_INPUT | MUX_MODE0)	/* rgmii0_rxd0.rgmii0_rxd0 */
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d12.rgmii1_txc */
-			DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d13.rgmii1_tctl */
-			DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d14.rgmii1_td3 */
-			DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d15.rgmii1_td2 */
-			DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d16.rgmii1_td1 */
-			DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3)	/* vin2a_d17.rgmii1_td0 */
-			DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3)	/* vin2a_d18.rgmii1_rclk */
-			DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3)	/* vin2a_d19.rgmii1_rctl */
-			DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3)	/* vin2a_d20.rgmii1_rd3 */
-			DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3)	/* vin2a_d21.rgmii1_rd2 */
-			DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3)	/* vin2a_d22.rgmii1_rd1 */
-			DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3)	/* vin2a_d23.rgmii1_rd0 */
-		>;
-
-	};
-
-	cpsw_sleep: cpsw_sleep {
-		pinctrl-single,pins = <
-			/* Slave 1 */
-			DRA7XX_CORE_IOPAD(0x3650, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3654, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3658, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x365c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3660, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3664, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3668, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x366c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3670, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3674, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3678, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x367c, MUX_MODE15)
-
-			/* Slave 2 */
-			DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15)
-		>;
-	};
-
-	davinci_mdio_default: davinci_mdio_default {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0)	/* mdio_d.mdio_d */
-			DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0)	/* mdio_clk.mdio_clk */
-		>;
-	};
-
-	davinci_mdio_sleep: davinci_mdio_sleep {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15)
-		>;
-	};
-
 	dcan1_pins_default: dcan1_pins_default {
 		pinctrl-single,pins = <
 			DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */

@@ -362,37 +164,10 @@
 			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
 		>;
 	};
-
-	atl_pins: pinmux_atl_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5)	/* xref_clk1.atl_clk1 */
-			DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5)	/* xref_clk2.atl_clk2 */
-		>;
-	};
-
-	mcasp3_pins: pinmux_mcasp3_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_aclkx */
-			DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_fsx */
-			DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_axr0 */
-			DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp3_axr1 */
-		>;
-	};
-
-	mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins {
-		pinctrl-single,pins = <
-			DRA7XX_CORE_IOPAD(0x3724, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3728, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x372c, MUX_MODE15)
-			DRA7XX_CORE_IOPAD(0x3730, MUX_MODE15)
-		>;
-	};
 };
 
 &i2c1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <400000>;
 
 	tps659038: tps659038 at 58 {

@@ -581,8 +356,6 @@
 
 &i2c2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 
 	pcf_hdmi: gpio at 26 {

@@ -602,41 +375,29 @@
 
 &i2c3 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
 };
 
 &mcspi1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi1_pins>;
 };
 
 &mcspi2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&mcspi2_pins>;
 };
 
 &uart1 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins>;
 	interrupts-extended = <&crossbar_mpu GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>,
 			      <&dra7_pmx_core 0x3e0>;
 };
 
 &uart2 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins>;
 };
 
 &uart3 {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart3_pins>;
 };
 
 &mmc1 {

@@ -732,14 +493,10 @@
 
 &usb1 {
 	dr_mode = "peripheral";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb1_pins>;
 };
 
 &usb2 {
 	dr_mode = "host";
-	pinctrl-names = "default";
-	pinctrl-0 = <&usb2_pins>;
 };
 
 &elm {

@@ -747,9 +504,12 @@
 };
 
 &gpmc {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&nand_flash_x16>;
+	/*
+	* For the existing IOdelay configuration via U-Boot we don't
+	* support NAND on dra7-evm. Keep it disabled. Enabling it
+	* requires a different configuration by U-Boot.
+	*/
+	status = "disabled";
 	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand at 0,0 {
 		compatible = "ti,omap2-nand";

@@ -845,9 +605,6 @@
 
 &mac {
 	status = "okay";
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&cpsw_default>;
-	pinctrl-1 = <&cpsw_sleep>;
 	dual_emac;
 };

@@ -863,12 +620,6 @@
 	dual_emac_res_vlan = <2>;
 };
 
-&davinci_mdio {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&davinci_mdio_default>;
-	pinctrl-1 = <&davinci_mdio_sleep>;
-};
-
 &dcan1 {
 	status = "ok";
 	pinctrl-names = "default", "sleep", "active";

@@ -878,9 +629,6 @@
 };
 
 &atl {
-	pinctrl-names = "default";
-	pinctrl-0 = <&atl_pins>;
-
 	assigned-clocks = <&abe_dpll_sys_clk_mux>,
 			  <&atl_gfclk_mux>,
 			  <&dpll_abe_ck>,

@@ -899,9 +647,6 @@
 
 &mcasp3 {
 	#sound-dai-cells = <0>;
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&mcasp3_pins>;
-	pinctrl-1 = <&mcasp3_sleep_pins>;
 
 	assigned-clocks = <&mcasp3_ahclkx_mux>;
 	assigned-clock-parents = <&atl_clkin2_ck>;

-- 
2.9.0

[PATCH v2 2/3] ARM: dts: dra7-evm: add pinmux configuration for mmc1/2

From: Sekhar Nori <hidden>
Date: 2016-12-13 11:29:46

From: Kishon Vijay Abraham I <redacted>

Add pinmux configuration for SD card slot and eMMC device
found on TI's DRA74x EVM.

Only the default modes are supported. For higher speed modes
(UHS and HS200) to function, we need full fledged IODelay support
in kernel. IODelay support is yet to be added.

Signed-off-by: Kishon Vijay Abraham I <redacted>
[nsekhar at ti.com: rebase to mainline/master, use IOPAD() macro,
		 update commit message]
Signed-off-by: Sekhar Nori <redacted>
---
 arch/arm/boot/dts/dra7-evm.dts | 31 +++++++++++++++++++++++++++++++
 1 file changed, 31 insertions(+)

diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index 80ebfd6a5c7b..40465d5277e6 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts

@@ -164,6 +164,33 @@
 			DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP)	/* wakeup0.off */
 		>;
 	};
+
+	mmc1_pins_default: mmc1_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14)	/* mmc1sdcd.gpio219 */
+			DRA7XX_CORE_IOPAD(0x3754, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_clk.clk */
+			DRA7XX_CORE_IOPAD(0x3758, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_cmd.cmd */
+			DRA7XX_CORE_IOPAD(0x375c, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat0.dat0 */
+			DRA7XX_CORE_IOPAD(0x3760, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat1.dat1 */
+			DRA7XX_CORE_IOPAD(0x3764, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat2.dat2 */
+			DRA7XX_CORE_IOPAD(0x3768, PIN_INPUT_PULLUP | MUX_MODE0) /* mmc1_dat3.dat3 */
+		>;
+	};
+
+	mmc2_pins_default: mmc2_pins_default {
+		pinctrl-single,pins = <
+			DRA7XX_CORE_IOPAD(0x349c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a23.mmc2_clk */
+			DRA7XX_CORE_IOPAD(0x34b0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_cs1.mmc2_cmd */
+			DRA7XX_CORE_IOPAD(0x34a0, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a24.mmc2_dat0 */
+			DRA7XX_CORE_IOPAD(0x34a4, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a25.mmc2_dat1 */
+			DRA7XX_CORE_IOPAD(0x34a8, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a26.mmc2_dat2 */
+			DRA7XX_CORE_IOPAD(0x34ac, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a27.mmc2_dat3 */
+			DRA7XX_CORE_IOPAD(0x348c, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a19.mmc2_dat4 */
+			DRA7XX_CORE_IOPAD(0x3490, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a20.mmc2_dat5 */
+			DRA7XX_CORE_IOPAD(0x3494, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a21.mmc2_dat6 */
+			DRA7XX_CORE_IOPAD(0x3498, PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_a22.mmc2_dat7 */
+		>;
+	};
 };
 
 &i2c1 {

@@ -402,6 +429,8 @@
 
 &mmc1 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins_default>;
 	vmmc-supply = <&evm_3v3_sd>;
 	vmmc_aux-supply = <&ldo1_reg>;
 	bus-width = <4>;

@@ -414,6 +443,8 @@
 
 &mmc2 {
 	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins_default>;
 	vmmc-supply = <&evm_3v3_sw>;
 	bus-width = <8>;
 };

-- 
2.9.0

[PATCH v2 3/3] ARM: dts: dra72-evm: drop NAND support

From: Sekhar Nori <hidden>
Date: 2016-12-13 11:29:47

For the existing IOdelay configuration via U-Boot, NAND is
not supported on dra72-evm (both Rev B and Rev C).

Disable it. Commit 46cfc8945887 ("ARM: dts: dra72-evm: Remove
pinmux configurations for erratum i869") has already removed
pinmuxing for NAND making it unusable.

Signed-off-by: Sekhar Nori <redacted>
---
 arch/arm/boot/dts/dra72-evm-common.dtsi | 7 ++++++-
 1 file changed, 6 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index e50fbeea96e0..64553476c678 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi

@@ -280,7 +280,12 @@
 };
 
 &gpmc {
-	status = "okay";
+	/*
+	 * For the existing IOdelay configuration via U-Boot we don't
+	 * support NAND on dra72-evm. Keep it disabled. Enabling it
+	 * requires a different configuration by U-Boot.
+	 */
+	status = "disabled";
 	ranges = <0 0 0x08000000 0x01000000>;	/* minimum GPMC partition = 16MB */
 	nand at 0,0 {
 		/* To use NAND, DIP switch SW5 must be set like so:

-- 
2.9.0

[PATCH v2 0/3] ARM: dts: dra7-evm: pinmuxing updates

From: tony@atomide.com (Tony Lindgren)
Date: 2017-01-05 16:55:55

* Sekhar Nori [off-list ref] [161213 03:30]:

Hi,

This patch series drops most of the pinmuxing from dra7-evm
to satisfy erratum i869 and adds missing eMMC and SD card pinmuxing.

The patches apply to latest linux-next. Tested on DRA74x EVM Rev H
using U-Boot 2016.11. Boot tested using NFS and basic testing carried
out on SD card, eMMC, Audio capture and playback.

NAND on DRA72 EVM is already unusable due to a similar patch. A patch
included here disables the GPMC node.

v1 -> v2:
- Add a patch to disable GPMC node on DRA72x EVM
- Disable GPMC node on DRA74x EVM

Kishon Vijay Abraham I (1):
  ARM: dts: dra7-evm: add pinmux configuration for mmc1/2

Sekhar Nori (2):
  ARM: dts: dra7-evm: Remove pinmux configurations for erratum i869
  ARM: dts: dra72-evm: drop NAND support

 arch/arm/boot/dts/dra7-evm.dts          | 282 ++++----------------------------
 arch/arm/boot/dts/dra72-evm-common.dtsi |   7 +-
 2 files changed, 35 insertions(+), 254 deletions(-)

Applying all into omap-for-v4.11/dt thanks.

Tony

`h`	back out one level
`j`	next message in thread
`k`	previous message in thread
`l`	drill in
`Esc`	close help / fold thread tree
`?`	toggle this help