[PATCH] ARM: dts: imx6: add support for Auvidea H100 board
From: l.stach@pengutronix.de (Lucas Stach)
Date: 2016-06-01 12:47:09
The Auvidea H100 is a baseboard for the SolidRun MicroSOM. Its primary feature is a Toshiba TC358743 HDMI to CSI decoder, allowing the board to work as HDMI passthrough and framegrabber. Signed-off-by: Lucas Stach <l.stach@pengutronix.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6q-h100.dts | 395 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 396 insertions(+) create mode 100644 arch/arm/boot/dts/imx6q-h100.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 06b6c2d695bf..4f936106f696 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile@@ -356,6 +356,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-gw54xx.dtb \ imx6q-gw551x.dtb \ imx6q-gw552x.dtb \ + imx6q-h100.dtb \ imx6q-hummingboard.dtb \ imx6q-icore-rqs.dtb \ imx6q-marsboard.dtb \
diff --git a/arch/arm/boot/dts/imx6q-h100.dts b/arch/arm/boot/dts/imx6q-h100.dts
new file mode 100644
index 000000000000..48058baae09a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-h100.dts@@ -0,0 +1,395 @@ +/* + * Copyright (C) 2015 Lucas Stach <kernel@pengutronix.de> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * version 2 as published by the Free Software Foundation. + * + * This file is distributed in the hope that it will be useful + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "imx6q.dtsi" +#include "imx6qdl-microsom.dtsi" +#include "imx6qdl-microsom-ar8035.dtsi" + +/ { + model = "Auvidea H100"; + compatible = "auvidea,h100", "fsl,imx6q"; + + aliases { + rtc0 = &rtc; + rtc1 = &snvs_rtc; + }; + + chosen { + stdout-path = &uart2; + }; + + hdmi_osc: hdmi-osc { + compatible = "fixed-clock"; + clock-output-names = "hdmi-osc"; + clock-frequency = <27000000>; + #clock-cells = <0>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_leds>; + + led0: power { + label = "power"; + gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led1: stream { + label = "stream"; + gpios = <&gpio2 29 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + led2: rec { + label = "rec"; + gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_hdmi: regulator-hdmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_reg_hdmi>; + compatible = "regulator-fixed"; + gpio = <&gpio2 20 0>; + regulator-name = "V_HDMI"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_nvcc_sd2: regulator-nvcc-sd2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_reg_nvcc_sd2>; + compatible = "regulator-gpio"; + regulator-name = "NVCC_SD2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-type = "voltage"; + regulator-boot-on; + regulator-always-on; + gpios = <&gpio4 9 GPIO_ACTIVE_HIGH>; + states = <1800000 0x1 + 3300000 0x0>; + }; + + reg_usbh1_vbus: regulator-usb-h1-vbus { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio1 0 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_usbh1_vbus>; + regulator-name = "USB_H1_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usbotg_vbus: regulator-usb-otg-vbus { + compatible = "regulator-fixed"; + enable-active-high; + gpio = <&gpio3 22 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_usbotg_vbus>; + regulator-name = "USB_OTG_VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + sound-sgtl5000 { + compatible = "fsl,imx-audio-sgtl5000"; + model = "H100 on-board codec"; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-ext-port = <5>; + mux-int-port = <1>; + ssi-controller = <&ssi1>; + }; +}; + +&audmux { + status = "okay"; +}; + +&hdmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_hdmi>; + ddc-i2c-bus = <&i2c2>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_i2c1>; + status = "okay"; + + eeprom: 24c02 at 51 { + compatible = "microchip,24c02", "at24"; + reg = <0x51>; + }; + + rtc: pcf8523 at 68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + }; + + sgtl5000: sgtl5000 at 0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_sgtl5000>; + clocks = <&clks IMX6QDL_CLK_CKO>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + }; + + tc358743: tc358743 at 0f { + compatible = "toshiba,tc358743"; + reg = <0x0f>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_tc358743>; + clocks = <&hdmi_osc>; + clock-names = "refclk"; + reset-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>; + /* IRQ has a wrong pull resistor which renders it useless */ + + port at 0 { + tc358743_out: endpoint { + remote-endpoint = <&mipi_csi2_in>; + data-lanes = <1 2 3 4>; + clock-lanes = <0>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <297000000>; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_i2c2>; + status = "okay"; +}; + +&iomuxc { + h100 { + pinctrl_h100_hdmi: h100-hdmi { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 + >; + }; + + pinctrl_h100_i2c1: h100-i2c1 { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_h100_i2c2: h100-i2c2 { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_h100_leds: pinctrl-h100-leds { + fsl,pins = < + MX6QDL_PAD_EIM_DA0__GPIO3_IO00 0x1b0b0 + MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0 + MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0 + >; + }; + + pinctrl_h100_reg_hdmi: h100-reg-hdmi { + fsl,pins = < + MX6QDL_PAD_EIM_A18__GPIO2_IO20 0x1b0b0 + >; + }; + + pinctrl_h100_reg_nvcc_sd2: h100-reg-nvcc-sd2 { + fsl,pins = < + MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x1b0b0 + >; + }; + + pinctrl_h100_sgtl5000: h100-sgtl5000 { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x130b0 + MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0 + MX6QDL_PAD_KEY_ROW0__AUD5_TXD 0x110b0 + MX6QDL_PAD_KEY_COL1__AUD5_TXFS 0x130b0 + MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0 + >; + }; + + pinctrl_h100_tc358743: h100-tc358743 { + fsl,pins = < + MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 + >; + }; + + pinctrl_h100_uart2: h100-uart2 { + fsl,pins = < + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + >; + }; + + pinctrl_h100_usbh1_vbus: hummingboard-usbh1-vbus { + fsl,pins = < + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0 + >; + }; + + pinctrl_h100_usbotg_id: hummingboard-usbotg-id { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059 + >; + }; + + pinctrl_h100_usbotg_vbus: hummingboard-usbotg-vbus { + fsl,pins = < + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_h100_usdhc2: h100-usdhc2 { + fsl,pins = < + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071 + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059 + >; + }; + + pinctrl_h100_usdhc2_100mhz: h100-usdhc2-100mhz { + fsl,pins = < + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071 + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9 + >; + }; + + pinctrl_h100_usdhc2_200mhz: h100-usdhc2-200mhz { + fsl,pins = < + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1f071 + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170f9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100f9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 + >; + }; + }; +}; + +&mipi_csi { + status = "okay"; + + port at 0 { + mipi_csi2_in: endpoint { + remote-endpoint = <&tc358743_out>; + data-lanes = <1 2 3 4>; + clock-lanes = <0>; + clock-noncontinuous; + link-frequencies = /bits/ 64 <297000000>; + }; + }; +}; + +&ssi1 { + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_uart2>; + status = "okay"; +}; + +&usbh1 { + disable-over-current; + vbus-supply = <®_usbh1_vbus>; + status = "okay"; +}; + +&usbotg { + disable-over-current; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_h100_usbotg_id>; + vbus-supply = <®_usbotg_vbus>; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_h100_usdhc2>; + pinctrl-1 = <&pinctrl_h100_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_h100_usdhc2_200mhz>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_nvcc_sd2>; + cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + status = "okay"; +};
--
2.8.1