[PATCH] ARM: dts: at91: sama5d2: add dma properties to UART nodes
From: Nicolas Ferre <hidden>
Date: 2016-01-26 16:29:50
The dmas/dma-names properties are added to the UART nodes. Note that additional properties are needed to enable them at the board level: check bindings for details. Signed-off-by: Nicolas Ferre <redacted> --- arch/arm/boot/dts/sama5d2.dtsi | 35 +++++++++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+)
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 3f750f6170f2..82d0c19e9720 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi@@ -880,6 +880,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xf801c000 0x100>; interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(35))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(36))>; + dma-names = "tx", "rx"; clocks = <&uart0_clk>; clock-names = "usart"; status = "disabled";
@@ -889,6 +896,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xf8020000 0x100>; interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(37))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(38))>; + dma-names = "tx", "rx"; clocks = <&uart1_clk>; clock-names = "usart"; status = "disabled";
@@ -898,6 +912,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xf8024000 0x100>; interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(39))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(40))>; + dma-names = "tx", "rx"; clocks = <&uart2_clk>; clock-names = "usart"; status = "disabled";
@@ -1016,6 +1037,13 @@ compatible = "atmel,at91sam9260-usart"; reg = <0xfc008000 0x100>; interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(41))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(42))>; + dma-names = "tx", "rx"; clocks = <&uart3_clk>; clock-names = "usart"; status = "disabled";
@@ -1024,6 +1052,13 @@ uart4: serial at fc00c000 { compatible = "atmel,at91sam9260-usart"; reg = <0xfc00c000 0x100>; + dmas = <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(43))>, + <&dma0 + (AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) | + AT91_XDMAC_DT_PERID(44))>; + dma-names = "tx", "rx"; interrupts = <28 IRQ_TYPE_LEVEL_HIGH 7>; clocks = <&uart4_clk>; clock-names = "usart";
--
2.1.3