[PATCH v3] imx: thermal: imx_get_temp might be called before sensor clock is prepared
From: Heiner Kallweit <hidden>
Date: 2014-10-08 17:17:59
Subsystem:
the rest, thermal · Maintainers:
Linus Torvalds, Rafael J. Wysocki, Daniel Lezcano
imx_get_temp might be called before the sensor clock is prepared
thus resulting in a timeout of the first attempt to read temp:
thermal thermal_zone0: failed to read out thermal zone 0
Happened to me on a Utilite Standard with IMX6 Dual SoC.
Reason is that in imx_thermal_probe thermal_zone_device_register
is called before the sensor clock is prepared.
thermal_zone_device_register however calls
thermal_zone_device_update which eventually calls imx_get_temp.
Fix this by preparing the clock before calling
thermal_zone_device_register.
Signed-off-by: Heiner Kallweit <redacted>
---
v2: revised error path. Bail out and tidy up properly if we can't
get the clock or fail to enable it
v3: don't print error message if getting clock returns EPROBE_DEFER
---
drivers/thermal/imx_thermal.c | 41 +++++++++++++++++++++++++----------------
1 file changed, 25 insertions(+), 16 deletions(-)
diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index 461bf3d..0e8ef55 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c@@ -521,6 +521,30 @@ static int imx_thermal_probe(struct platform_device *pdev) return ret; } + data->thermal_clk = devm_clk_get(&pdev->dev, NULL); + if (IS_ERR(data->thermal_clk)) { + ret = PTR_ERR(data->thermal_clk); + if (ret != -EPROBE_DEFER) + dev_err(&pdev->dev, + "failed to get thermal clk: %d\n", ret); + cpufreq_cooling_unregister(data->cdev); + return ret; + } + + /* + * Thermal sensor needs clk on to get correct value, normally + * we should enable its clk before taking measurement and disable + * clk after measurement is done, but if alarm function is enabled, + * hardware will auto measure the temperature periodically, so we + * need to keep the clk always on for alarm function. + */ + ret = clk_prepare_enable(data->thermal_clk); + if (ret) { + dev_err(&pdev->dev, "failed to enable thermal clk: %d\n", ret); + cpufreq_cooling_unregister(data->cdev); + return ret; + } + data->tz = thermal_zone_device_register("imx_thermal_zone", IMX_TRIP_NUM, BIT(IMX_TRIP_PASSIVE), data,
@@ -531,26 +555,11 @@ static int imx_thermal_probe(struct platform_device *pdev) ret = PTR_ERR(data->tz); dev_err(&pdev->dev, "failed to register thermal zone device %d\n", ret); + clk_disable_unprepare(data->thermal_clk); cpufreq_cooling_unregister(data->cdev); return ret; } - data->thermal_clk = devm_clk_get(&pdev->dev, NULL); - if (IS_ERR(data->thermal_clk)) { - dev_warn(&pdev->dev, "failed to get thermal clk!\n"); - } else { - /* - * Thermal sensor needs clk on to get correct value, normally - * we should enable its clk before taking measurement and disable - * clk after measurement is done, but if alarm function is enabled, - * hardware will auto measure the temperature periodically, so we - * need to keep the clk always on for alarm function. - */ - ret = clk_prepare_enable(data->thermal_clk); - if (ret) - dev_warn(&pdev->dev, "failed to enable thermal clk: %d\n", ret); - } - /* Enable measurements at ~ 10 Hz */ regmap_write(map, TEMPSENSE1 + REG_CLR, TEMPSENSE1_MEASURE_FREQ); measure_freq = DIV_ROUND_UP(32768, 10); /* 10 Hz */ --
2.1.2