Re: [PATCH] ARM: dt: sun7i: Add Banana Pi board
From: Maxime Ripard <hidden>
Date: 2014-07-31 09:58:00
Hi Hans, On Tue, Jul 29, 2014 at 07:02:28PM +0200, Hans de Goede wrote:
quoted hunk
The Banana Pi is an A20 based development board using Raspberry Pi compatible IO headers. It comes with 1 GB RAM, 1 Gb ethernet, 2x USB host, sata, hdmi and stereo audio out + various expenansion headers: http://www.bananapi.org/ Signed-off-by: Hans de Goede <redacted> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun7i-a20-bananapi.dts | 183 +++++++++++++++++++++++++++++++ 2 files changed, 184 insertions(+) create mode 100644 arch/arm/boot/dts/sun7i-a20-bananapi.dtsdiff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index bdbc84a..440e037 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile@@ -379,6 +379,7 @@ dtb-$(CONFIG_MACH_SUN6I) += \ sun6i-a31-hummingbird.dtb \ sun6i-a31-m9.dtb dtb-$(CONFIG_MACH_SUN7I) += \ + sun7i-a20-bananapi.dtb \ sun7i-a20-cubieboard2.dtb \ sun7i-a20-cubietruck.dtb \ sun7i-a20-i12-tvbox.dtb \diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts new file mode 100644 index 0000000..0332b82 --- /dev/null +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts@@ -0,0 +1,183 @@ +/* + * Copyright 2014 Hans de Goede <hdegoede@redhat.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "LeMaker Banana Pi"; + compatible = "lemaker,bananapi", "allwinner,sun7i-a20"; + + soc at 01c00000 { + spi0: spi at 01c05000 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins_a>; + status = "okay"; + }; + + mmc0: mmc at 01c0f000 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>; + vmmc-supply = <®_vcc3v3>; + bus-width = <4>; + cd-gpios = <&pio 7 10 0>; /* PH10 */ + cd-inverted; + status = "okay"; + }; + + usbphy: phy at 01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb at 01c14000 { + status = "okay"; + }; + + ohci0: usb at 01c14400 { + status = "okay"; + }; + + ahci: sata at 01c18000 { + status = "okay"; + }; + + ehci1: usb at 01c1c000 { + status = "okay"; + }; + + ohci1: usb at 01c1c400 { + status = "okay"; + }; + + pinctrl at 01c20800 { + uart3_pins_bananapi: uart3_pin at 0 { + allwinner,pins = "PH0", "PH1"; + allwinner,function = "uart3"; + allwinner,drive = <0>; + allwinner,pull = <0>; + };
That node should be in the DTSI
+
+ mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <0>;
+ allwinner,pull = <1>;
+ };
+
+ gmac_power_pin_bananapi: gmac_power_pin at 0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+
+ led_pins_bananapi: led_pins at 0 {
+ allwinner,pins = "PH24";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <0>;
+ allwinner,pull = <0>;
+ };
+ };
+
+ ir0: ir at 01c21800 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_pins_a>;
+ status = "okay";
+ };
+
+ uart0: serial at 01c28000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+ };
+
+ uart3: serial at 01c28c00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins_bananapi>;
+ status = "okay";
+ };
+
+ uart7: serial at 01c29c00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart7_pins_a>;
+ status = "okay";
+ };
+
+ i2c0: i2c at 01c2ac00 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 8>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+ };
+
+ i2c2: i2c at 01c2b400 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "okay";
+ };
+
+ gmac: ethernet at 01c50000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bananapi>;
+
+ green {
+ label = "bananapi:green:usr";
+ gpios = <&pio 7 24 0>;
+ };
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ status = "okay";
+ };
+
+ reg_usb2_vbus: usb2-vbus {
+ status = "okay";
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bananapi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <50000>;
+ enable-active-high;
+ gpio = <&pio 7 23 0>;
+ };
+};Looks fine otherwise, thanks! Maxime -- Maxime Ripard, Free Electrons Embedded Linux, Kernel and Android engineering http://free-electrons.com -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140731/6f761c60/attachment.sig>