# \[PATCH V2 1/6\] ahci: imx: Explicitly clear IMX6Q\_GPR13\_SATA\_MPLL\_CLK\_EN

- From: Troy Kisky \<hidden\>
- Date: 2013-11-22 19:26:45 
- List: linux-arm-kernel
- Page: https://ratatoskr.run/linux-arm-kernel/2013/11/8666233
- Thread: https://ratatoskr.run/linux-arm-kernel/2013/11/8666194/t.md

```text
On 11/22/2013 4:04 AM, Marek Vasut wrote:
> We must clear this IMX6Q_GPR13_SATA_MPLL_CLK_EN bit on i.MX6Q, otherwise
> Linux will fail to find the attached drive on some boards.
>
> This entire fix was:
> Reported-by: Eric Nelson <redacted>
>
> Signed-off-by: Marek Vasut <marex@denx.de>
> Cc: Shawn Guo <redacted>
> Cc: Richard Zhu <redacted>
> Cc: Tejun Heo <tj@kernel.org>
> Cc: Linux-IDE <redacted>
> ---
>   drivers/ata/ahci_imx.c | 3 ++-
>   1 file changed, 2 insertions(+), 1 deletion(-)
>
> V2: Update the value in the comment from 0x7ffffffd to 0x7ffffffe
>
> diff --git a/drivers/ata/ahci_imx.c b/drivers/ata/ahci_imx.c
> index ae2d73f..14227d1 100644
> --- a/drivers/ata/ahci_imx.c
> +++ b/drivers/ata/ahci_imx.c
> @@ -113,7 +113,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
>   	/*
>   	 * set PHY Paremeters, two steps to configure the GPR13,
>   	 * one write for rest of parameters, mask of first write
> -	 * is 0x07fffffd, and the other one write for setting
> +	 * is 0x07fffffe, and the other one write for setting

0x07ffffff, d+2 = f,
bit 1 is IMX6Q_GPR13_SATA_MPLL_CLK_EN, which you just added
bit 0 is IMX6Q_GPR13_SATA_TX_EDGE_RATE, which is also in your expression

>   	 * the mpll_clk_en.
>   	 */
>   	regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
> @@ -125,6 +125,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)
>   			| IMX6Q_GPR13_SATA_TX_BOOST_MASK
>   			| IMX6Q_GPR13_SATA_TX_LVL_MASK
>   			| IMX6Q_GPR13_SATA_TX_EDGE_RATE
> +			| IMX6Q_GPR13_SATA_MPLL_CLK_EN
>   			, IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB
>   			| IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M
>   			| IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
```
