Hi Mark,

On Wed, Nov 28, 2012 at 10:55 AM, Sangbeom Kim [off-list ref] wrote:

quoted

quoted

There's some problems with this binding.  The main one is the gpios
property the format of which isn't specified at all.

quoted

All of above gpio property is i2s.
That is,
+     gpios = <&gpz 0 2 0 0>, -> SCLK
+             <&gpz 1 2 0 0>,   ->  CDCLK
+             <&gpz 2 2 0 0>,   -> LRCK
+             <&gpz 3 2 0 0>,   -> SDI
+             <&gpz 4 2 0 0>,   -> SDO[0]
+             <&gpz 5 2 0 0>,   -> SDO[1]
+             <&gpz 6 2 0 0>;   -> SDO[2]

quoted

Do you want like a below one?
+sclk-gpios = <&gpz 0 2 0 0>,
+cdclk-gpios = <&gpz 1 2 0 0>, ...

That would be nice but what I was really looking for was some indiciation in the binding document as
to what all this stuff means - it should really say what gpz is (though I can figure that out) and
it definitely needs to say what the four numbers are.

quoted

quoted

The requirement for an alias is also very odd, where does that come from?

quoted

I don't know that Which one is odd. Please let me know.

Having them at all is odd - it's not something other DT bindings have needed and there was nothing
saying what it was for.

What is the exact requirement here? Should I remove the alias ids or
I2S1 and I2S2 nodes as they are in disabled state? This is done same
way as SPI and I2C. Please explain me.

quoted

quoted

Some of the code also looks very peculiar, like the fact that it's
generating a clock name i2s_opclk%d rather than hard coding the
clock, the physical clock would normally be resolved based on the
struct device.

quoted

This is to handle all of Samsung SOCs i2c clock mux.
Please look at below clk_lookup table

quoted

In case of 6410, clk_lookup
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk0", &clk_i2s0),
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk1", &clk_audio_bus0.clk),
+     CLKDEV_INIT("samsung-i2s.1", "i2s_opclk0", &clk_i2s1),
+     CLKDEV_INIT("samsung-i2s.1", "i2s_opclk1", &clk_audio_bus1.clk),
+#ifdef CONFIG_CPU_S3C6410
+     CLKDEV_INIT("samsung-i2s.2", "i2s_opclk0", &clk_i2s2),
+     CLKDEV_INIT("samsung-i2s.2", "i2s_opclk1", &clk_audio_bus2.clk),

quoted

In case of exynos5, clk_lookup
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk0", &exynos5_clk_sclk_i2s.clk),
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk1",
+&exynos5_clk_i2s_bus.clk),

quoted

We try to handle clock source of i2s by only i2s_opclk0 and i2s_opclk1.
Each SOCs have different clock source.
Is this wrong approach?

That makes sense but why is the driver not just requesting by name rather than having code to
generate the names, and why is this mixed in with the patch adding DT support?

Thanks
Padma