[PATCH v2] ARM: zynq: Allow UART1 to be used as DEBUG_LL console.
From: Nick Bowler <hidden>
Date: 2012-10-29 18:20:07
The main UART on the Xilinx ZC702 board is UART1, located at address e0001000. Add a Kconfig option to select this device as the low-level debugging port. This allows the really early boot printouts to reach the USB serial adaptor on this board. For consistency's sake, add a choice entry for UART0 even though it is the the default if UART1 is not selected. Signed-off-by: Nick Bowler <redacted> Tested-by: Josh Cartwright <redacted> --- v2: rebase on newest patch series, signoff. This should apply cleanly on top of Josh Cartwright's v5 "zynq subarch cleanups" series. arch/arm/Kconfig.debug | 17 +++++++++++++++++ arch/arm/mach-zynq/common.c | 6 +++--- arch/arm/mach-zynq/include/mach/zynq_soc.h | 16 +++++++++++----- 3 files changed, 31 insertions(+), 8 deletions(-)
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index b0f3857b3a4c..7754d51f2b19 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug@@ -132,6 +132,23 @@ choice their output to UART1 serial port on DaVinci TNETV107X devices. + config DEBUG_ZYNQ_UART0 + bool "Kernel low-level debugging on Xilinx Zynq using UART0" + depends on ARCH_ZYNQ + help + Say Y here if you want the debug print routines to direct + their output to UART0 on the Zynq platform. + + config DEBUG_ZYNQ_UART1 + bool "Kernel low-level debugging on Xilinx Zynq using UART1" + depends on ARCH_ZYNQ + help + Say Y here if you want the debug print routines to direct + their output to UART1 on the Zynq platform. + + If you have a ZC702 board and want early boot messages to + appear on the USB serial adaptor, select this option. + config DEBUG_DC21285_PORT bool "Kernel low-level debugging messages via footbridge serial port" depends on FOOTBRIDGE
diff --git a/arch/arm/mach-zynq/common.c b/arch/arm/mach-zynq/common.c
index ba8d14f78d4d..93b91059faab 100644
--- a/arch/arm/mach-zynq/common.c
+++ b/arch/arm/mach-zynq/common.c@@ -84,9 +84,9 @@ static struct map_desc io_desc[] __initdata = { #ifdef CONFIG_DEBUG_LL { - .virtual = UART0_VIRT, - .pfn = __phys_to_pfn(UART0_PHYS), - .length = UART0_SIZE, + .virtual = LL_UART_VADDR, + .pfn = __phys_to_pfn(LL_UART_PADDR), + .length = UART_SIZE, .type = MT_DEVICE, }, #endif
diff --git a/arch/arm/mach-zynq/include/mach/zynq_soc.h b/arch/arm/mach-zynq/include/mach/zynq_soc.h
index 1b8bf0ecbcb0..7f4f38bcada9 100644
--- a/arch/arm/mach-zynq/include/mach/zynq_soc.h
+++ b/arch/arm/mach-zynq/include/mach/zynq_soc.h@@ -25,8 +25,9 @@ * address that is known to work. */ #define UART0_PHYS 0xE0000000 -#define UART0_SIZE SZ_4K -#define UART0_VIRT 0xF0001000 +#define UART1_PHYS 0xE0001000 +#define UART_SIZE SZ_4K +#define UART_VIRT 0xF0001000 #define TTC0_PHYS 0xF8001000 #define TTC0_SIZE SZ_4K
@@ -36,12 +37,17 @@ #define SCU_PERIPH_SIZE SZ_8K #define SCU_PERIPH_VIRT (TTC0_VIRT - SCU_PERIPH_SIZE) +#if IS_ENABLED(CONFIG_DEBUG_ZYNQ_UART1) +# define LL_UART_PADDR UART1_PHYS +# define LL_UART_VADDR UART_VIRT +#else +# define LL_UART_PADDR UART0_PHYS +# define LL_UART_VADDR UART_VIRT +#endif + /* The following are intended for the devices that are mapped early */ #define TTC0_BASE IOMEM(TTC0_VIRT) #define SCU_PERIPH_BASE IOMEM(SCU_PERIPH_VIRT) -#define LL_UART_PADDR UART0_PHYS -#define LL_UART_VADDR UART0_VIRT - #endif
--
1.7.8.6