[PATCH v7 0/7] omap: musb: Add device tree support

@@ -5885,6 +5885,11 @@ static struct omap_hwmod_addr_space omap44xx_usb_otg_hs_addrs[] = {
 		.pa_end		= 0x4a0ab003,
 		.flags		= ADDR_TYPE_RT
 	},
+	{
+		.pa_start	= 0x4a00233c,
+		.pa_end		= 0x4a00233f,
+		.flags		= ADDR_TYPE_RT
+	},
 	{ }
 };
 

@@ -0,0 +1,21 @@
+USB COMPARATOR OF TWL CHIPS
+
+TWL6030 USB COMPARATOR
+ - compatible : Should be "ti,twl6030-usb"
+ - interrupts : Two interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts when
+   the controller has to act as host and the second interrupt number is the
+   usb interrupt number that raises VBUS interrupts when the controller has to
+   act as device
+ - usb-supply : phandle to the regulator device tree node. It should be vusb
+   if it is twl6030 or ldousb if it is twl6025 subclass.
+
+twl6030-usb {
+	compatible = "ti,twl6030-usb";
+	interrupts = < 4 10 >;
+};
+
+Board specific device node entry
+&twl6030-usb {
+	usb-supply = <&vusb>;
+};

@@ -105,7 +105,7 @@ struct twl6030_usb {
 	u8			asleep;
 	bool			irq_enabled;
 	bool			vbus_enable;
-	unsigned long		features;
+	const char		*regulator;
 };
 
 #define	comparator_to_twl(x) container_of((x), struct twl6030_usb, comparator)

@@ -153,13 +153,6 @@ static int twl6030_start_srp(struct phy_companion *comparator)
 
 static int twl6030_usb_ldo_init(struct twl6030_usb *twl)
 {
-	char *regulator_name;
-
-	if (twl->features & TWL6025_SUBCLASS)
-		regulator_name = "ldousb";
-	else
-		regulator_name = "vusb";
-
 	/* Set to OTG_REV 1.3 and turn on the ID_WAKEUP_COMP */
 	twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x1, TWL6030_BACKUP_REG);
 

@@ -169,7 +162,7 @@ static int twl6030_usb_ldo_init(struct twl6030_usb *twl)
 	/* Program MISC2 register and set bit VUSB_IN_VBAT */
 	twl6030_writeb(twl, TWL6030_MODULE_ID0 , 0x10, TWL6030_MISC2);
 
-	twl->usb3v3 = regulator_get(twl->dev, regulator_name);
+	twl->usb3v3 = regulator_get(twl->dev, twl->regulator);
 	if (IS_ERR(twl->usb3v3))
 		return -ENODEV;
 

@@ -322,9 +315,9 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 	u32 ret;
 	struct twl6030_usb	*twl;
 	int			status, err;
-	struct twl4030_usb_data *pdata;
-	struct device *dev = &pdev->dev;
-	pdata = dev->platform_data;
+	struct device_node	*np = pdev->dev.of_node;
+	struct device		*dev = &pdev->dev;
+	struct twl4030_usb_data	*pdata = dev->platform_data;
 
 	twl = devm_kzalloc(dev, sizeof *twl, GFP_KERNEL);
 	if (!twl)

@@ -333,7 +326,6 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 	twl->dev		= &pdev->dev;
 	twl->irq1		= platform_get_irq(pdev, 0);
 	twl->irq2		= platform_get_irq(pdev, 1);
-	twl->features		= pdata->features;
 	twl->linkstat		= OMAP_MUSB_UNKNOWN;
 
 	twl->comparator.set_vbus	= twl6030_set_vbus;

@@ -345,6 +337,18 @@ static int __devinit twl6030_usb_probe(struct platform_device *pdev)
 		return -EPROBE_DEFER;
 	}
 
+	if (np) {
+		twl->regulator = "usb";
+	} else if (pdata) {
+		if (pdata->features & TWL6025_SUBCLASS)
+			twl->regulator = "ldousb";
+		else
+			twl->regulator = "vusb";
+	} else {
+		dev_err(&pdev->dev, "twl6030 initialized without pdata\n");
+		return -EINVAL;
+	}
+
 	/* init spinlock for workqueue */
 	spin_lock_init(&twl->lock);
 

@@ -406,12 +410,21 @@ static int __exit twl6030_usb_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static const struct of_device_id twl6030_usb_id_table[] = {
+	{ .compatible = "ti,twl6030-usb" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, twl6030_usb_id_table);
+#endif
+
 static struct platform_driver twl6030_usb_driver = {
 	.probe		= twl6030_usb_probe,
 	.remove		= __exit_p(twl6030_usb_remove),
 	.driver		= {
 		.name	= "twl6030_usb",
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(twl6030_usb_id_table),
 	},
 };
 

@@ -1,4 +1,4 @@
-OMAP USB PHY
+OMAP USB PHY AND GLUE
 
 OMAP USB2 PHY
 

@@ -15,3 +15,35 @@ usb2phy at 4a0ad080 {
 	reg = <0x4a0ad080 0x58>,
 		<0x4a002300 0x1>;
 };
+
+OMAP MUSB GLUE
+ - compatible : Should be "ti,musb-omap2430"
+ - ti,hwmods : must be "usb_otg_hs"
+ - multipoint : Should be "1" indicating the musb controller supports
+   multipoint. This is a MUSB configuration-specific setting.
+ - num_eps : Specifies the number of endpoints. This is also a
+   MUSB configuration-specific setting. Should be set to "16"
+ - ram_bits : Specifies the ram address size. Should be set to "12"
+ - interface_type : This is a board specific setting to describe the type of
+   interface between the controller and the phy. It should be "0" or "1"
+   specifying ULPI and UTMI respectively.
+ - mode : Should be "3" to represent OTG. "1" signifies HOST and "2"
+   represents PERIPHERAL.
+ - power : Should be "50". This signifies the controller can supply upto
+   100mA when operating in host mode.
+
+SOC specific device node entry
+usb_otg_hs: usb_otg_hs at 4a0ab000 {
+	compatible = "ti,musb-omap2430";
+	ti,hwmods = "usb_otg_hs";
+	multipoint = <1>;
+	num_eps = <16>;
+	ram_bits = <12>;
+};
+
+Board specific device node entry
+&usb_otg_hs {
+	interface_type = <1>;
+	mode = <3>;
+	power = <50>;
+};

@@ -30,6 +30,7 @@
 #include <linux/init.h>
 #include <linux/list.h>
 #include <linux/io.h>
+#include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/dma-mapping.h>
 #include <linux/pm_runtime.h>

@@ -469,8 +470,11 @@ static u64 omap2430_dmamask = DMA_BIT_MASK(32);
 static int __devinit omap2430_probe(struct platform_device *pdev)
 {
 	struct musb_hdrc_platform_data	*pdata = pdev->dev.platform_data;
+	struct omap_musb_board_data	*data;
 	struct platform_device		*musb;
 	struct omap2430_glue		*glue;
+	struct device_node		*np = pdev->dev.of_node;
+	struct musb_hdrc_config		*config;
 	struct resource			*res;
 	int				ret = -ENOMEM;
 

@@ -500,6 +504,42 @@ static int __devinit omap2430_probe(struct platform_device *pdev)
 	if (glue->control_otghs == NULL)
 		dev_dbg(&pdev->dev, "Failed to obtain control memory\n");
 
+	if (np) {
+		pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
+		if (!pdata) {
+			dev_err(&pdev->dev,
+				"failed to allocate musb platfrom data\n");
+			ret = -ENOMEM;
+			goto err1;
+		}
+
+		data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+		if (!data) {
+			dev_err(&pdev->dev,
+					"failed to allocate musb board data\n");
+			ret = -ENOMEM;
+			goto err1;
+		}
+
+		config = devm_kzalloc(&pdev->dev, sizeof(*config), GFP_KERNEL);
+		if (!data) {
+			dev_err(&pdev->dev,
+				"failed to allocate musb hdrc config\n");
+			goto err1;
+		}
+
+		of_property_read_u32(np, "mode", (u32 *)&pdata->mode);
+		of_property_read_u32(np, "interface_type",
+						(u32 *)&data->interface_type);
+		of_property_read_u32(np, "num_eps", (u32 *)&config->num_eps);
+		of_property_read_u32(np, "ram_bits", (u32 *)&config->ram_bits);
+		of_property_read_u32(np, "power", (u32 *)&pdata->power);
+		config->multipoint = of_property_read_bool(np, "multipoint");
+
+		pdata->board_data	= data;
+		pdata->config		= config;
+	}
+
 	pdata->platform_ops		= &omap2430_ops;
 
 	platform_set_drvdata(pdev, glue);

@@ -596,12 +636,26 @@ static struct dev_pm_ops omap2430_pm_ops = {
 #define DEV_PM_OPS	NULL
 #endif
 
+#ifdef CONFIG_OF
+static const struct of_device_id omap2430_id_table[] = {
+	{
+		.compatible = "ti,omap4-musb"
+	},
+	{
+		.compatible = "ti,omap3-musb"
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, omap2430_id_table);
+#endif
+
 static struct platform_driver omap2430_driver = {
 	.probe		= omap2430_probe,
 	.remove		= __devexit_p(omap2430_remove),
 	.driver		= {
 		.name	= "musb-omap2430",
 		.pm	= DEV_PM_OPS,
+		.of_match_table = of_match_ptr(omap2430_id_table),
 	},
 };
 

@@ -31,144 +31,6 @@
 #include <plat/usb.h>
 #include "control.h"
 
-/* OMAP control module register for UTMI PHY */
-#define CONTROL_DEV_CONF		0x300
-#define PHY_PD				0x1
-
-#define USBOTGHS_CONTROL		0x33c
-#define	AVALID				BIT(0)
-#define	BVALID				BIT(1)
-#define	VBUSVALID			BIT(2)
-#define	SESSEND				BIT(3)
-#define	IDDIG				BIT(4)
-
-static struct clk *phyclk, *clk48m, *clk32k;
-static void __iomem *ctrl_base;
-static int usbotghs_control;
-
-int omap4430_phy_init(struct device *dev)
-{
-	ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
-	if (!ctrl_base) {
-		pr_err("control module ioremap failed\n");
-		return -ENOMEM;
-	}
-	/* Power down the phy */
-	__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-	if (!dev) {
-		iounmap(ctrl_base);
-		return 0;
-	}
-
-	phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
-	if (IS_ERR(phyclk)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n");
-		iounmap(ctrl_base);
-		return PTR_ERR(phyclk);
-	}
-
-	clk48m = clk_get(dev, "ocp2scp_usb_phy_phy_48m");
-	if (IS_ERR(clk48m)) {
-		dev_err(dev, "cannot clk_get ocp2scp_usb_phy_phy_48m\n");
-		clk_put(phyclk);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk48m);
-	}
-
-	clk32k = clk_get(dev, "usb_phy_cm_clk32k");
-	if (IS_ERR(clk32k)) {
-		dev_err(dev, "cannot clk_get usb_phy_cm_clk32k\n");
-		clk_put(phyclk);
-		clk_put(clk48m);
-		iounmap(ctrl_base);
-		return PTR_ERR(clk32k);
-	}
-	return 0;
-}
-
-int omap4430_phy_set_clk(struct device *dev, int on)
-{
-	static int state;
-
-	if (on && !state) {
-		/* Enable the phy clocks */
-		clk_enable(phyclk);
-		clk_enable(clk48m);
-		clk_enable(clk32k);
-		state = 1;
-	} else if (state) {
-		/* Disable the phy clocks */
-		clk_disable(phyclk);
-		clk_disable(clk48m);
-		clk_disable(clk32k);
-		state = 0;
-	}
-	return 0;
-}
-
-int omap4430_phy_power(struct device *dev, int ID, int on)
-{
-	if (on) {
-		if (ID)
-			/* enable VBUS valid, IDDIG groung */
-			__raw_writel(AVALID | VBUSVALID, ctrl_base +
-							USBOTGHS_CONTROL);
-		else
-			/*
-			 * Enable VBUS Valid, AValid and IDDIG
-			 * high impedance
-			 */
-			__raw_writel(IDDIG | AVALID | VBUSVALID,
-						ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable session END and IDIG to high impedance. */
-		__raw_writel(SESSEND | IDDIG, ctrl_base +
-					USBOTGHS_CONTROL);
-	}
-	return 0;
-}
-
-int omap4430_phy_suspend(struct device *dev, int suspend)
-{
-	if (suspend) {
-		/* Disable the clocks */
-		omap4430_phy_set_clk(dev, 0);
-		/* Power down the phy */
-		__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-
-		/* save the context */
-		usbotghs_control = __raw_readl(ctrl_base + USBOTGHS_CONTROL);
-	} else {
-		/* Enable the internel phy clcoks */
-		omap4430_phy_set_clk(dev, 1);
-		/* power on the phy */
-		if (__raw_readl(ctrl_base + CONTROL_DEV_CONF) & PHY_PD) {
-			__raw_writel(~PHY_PD, ctrl_base + CONTROL_DEV_CONF);
-			mdelay(200);
-		}
-
-		/* restore the context */
-		__raw_writel(usbotghs_control, ctrl_base + USBOTGHS_CONTROL);
-	}
-
-	return 0;
-}
-
-int omap4430_phy_exit(struct device *dev)
-{
-	if (ctrl_base)
-		iounmap(ctrl_base);
-	if (phyclk)
-		clk_put(phyclk);
-	if (clk48m)
-		clk_put(clk48m);
-	if (clk32k)
-		clk_put(clk32k);
-
-	return 0;
-}
-
 void am35x_musb_reset(void)
 {
 	u32	regval;

@@ -250,11 +250,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
 
 #if defined(CONFIG_ARCH_OMAP4)
 static struct twl4030_usb_data omap4_usb_pdata = {
-	.phy_init	= omap4430_phy_init,
-	.phy_exit	= omap4430_phy_exit,
-	.phy_power	= omap4430_phy_power,
-	.phy_set_clock	= omap4430_phy_set_clk,
-	.phy_suspend	= omap4430_phy_suspend,
 };
 
 static struct regulator_init_data omap4_vdac_idata = {

@@ -117,7 +117,4 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
 	dev->dma_mask = &musb_dmamask;
 	dev->coherent_dma_mask = musb_dmamask;
 	put_device(dev);
-
-	if (cpu_is_omap44xx())
-		omap4430_phy_init(dev);
 }

@@ -8,3 +8,6 @@ properties:
 
 Sub-nodes:
 All the devices connected to ocp2scp are described using sub-node to ocp2scp
+- usb2phy :
+   The binding details of usb2phy can be found in:
+   Documentation/devicetree/bindings/usb/omap-usb.txt

@@ -0,0 +1,17 @@
+OMAP USB PHY
+
+OMAP USB2 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb2"
+ - reg : Address and length of the register set for the device. Also
+add the address of control module dev conf register until a driver for
+control module is added
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb2phy at 4a0ad080 {
+	compatible = "ti,omap-usb2";
+	reg = <0x4a0ad080 0x58>,
+		<0x4a002300 0x1>;
+};

@@ -4,6 +4,16 @@
 comment "USB Physical Layer drivers"
 	depends on USB || USB_GADGET
 
+config OMAP_USB2
+	tristate "OMAP USB2 PHY Driver"
+	depends on OMAP_OCP2SCP
+	select USB_OTG_UTILS
+	help
+	  Enable this to support the transceiver that is part of SOC. This
+	  driver takes care of all the PHY functionality apart from comparator.
+	  The USB OTG controller communicates with the comparator using this
+	  driver.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET

@@ -4,4 +4,5 @@
 
 ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
 
+obj-$(CONFIG_OMAP_USB2)			+= omap-usb2.o
 obj-$(CONFIG_USB_ISP1301)		+= isp1301.o

@@ -0,0 +1,271 @@
+/*
+ * omap-usb2.c - USB PHY, talking to musb controller in OMAP.
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/usb/omap_usb.h>
+#include <linux/usb/phy_companion.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/delay.h>
+
+/**
+ * omap_usb2_set_comparator - links the comparator present in the sytem with
+ *	this phy
+ * @comparator - the companion phy(comparator) for this phy
+ *
+ * The phy companion driver should call this API passing the phy_companion
+ * filled with set_vbus and start_srp to be used by usb phy.
+ *
+ * For use by phy companion driver
+ */
+int omap_usb2_set_comparator(struct phy_companion *comparator)
+{
+	struct omap_usb	*phy;
+	struct usb_phy	*x = usb_get_phy(USB_PHY_TYPE_USB2);
+
+	if (IS_ERR(x))
+		return -ENODEV;
+
+	phy = phy_to_omapusb(x);
+	phy->comparator = comparator;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(omap_usb2_set_comparator);
+
+/**
+ * omap_usb_phy_power - power on/off the phy using control module reg
+ * @phy: struct omap_usb *
+ * @on: 0 or 1, based on powering on or off the PHY
+ *
+ * XXX: Remove this function once control module driver gets merged
+ */
+static void omap_usb_phy_power(struct omap_usb *phy, int on)
+{
+	u32 val;
+
+	if (on) {
+		val = readl(phy->control_dev);
+		if (val & PHY_PD) {
+			writel(~PHY_PD, phy->control_dev);
+			/* XXX: add proper documentation for this delay */
+			mdelay(200);
+		}
+	} else {
+		writel(PHY_PD, phy->control_dev);
+	}
+}
+
+static int omap_usb_set_vbus(struct usb_otg *otg, bool enabled)
+{
+	struct omap_usb *phy = phy_to_omapusb(otg->phy);
+
+	if (!phy->comparator)
+		return -ENODEV;
+
+	return phy->comparator->set_vbus(phy->comparator, enabled);
+}
+
+static int omap_usb_start_srp(struct usb_otg *otg)
+{
+	struct omap_usb *phy = phy_to_omapusb(otg->phy);
+
+	if (!phy->comparator)
+		return -ENODEV;
+
+	return phy->comparator->start_srp(phy->comparator);
+}
+
+static int omap_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	struct usb_phy	*phy = otg->phy;
+
+	otg->host = host;
+	if (!host)
+		phy->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int omap_usb_set_peripheral(struct usb_otg *otg,
+		struct usb_gadget *gadget)
+{
+	struct usb_phy	*phy = otg->phy;
+
+	otg->gadget = gadget;
+	if (!gadget)
+		phy->state = OTG_STATE_UNDEFINED;
+
+	return 0;
+}
+
+static int omap_usb2_suspend(struct usb_phy *x, int suspend)
+{
+	u32 ret;
+	struct omap_usb *phy = phy_to_omapusb(x);
+
+	if (suspend && !phy->is_suspended) {
+		omap_usb_phy_power(phy, 0);
+		pm_runtime_put_sync(phy->dev);
+		phy->is_suspended = 1;
+	} else if (!suspend && phy->is_suspended) {
+		ret = pm_runtime_get_sync(phy->dev);
+		if (ret < 0) {
+			dev_err(phy->dev, "get_sync failed with err %d\n",
+									ret);
+			return ret;
+		}
+		omap_usb_phy_power(phy, 1);
+		phy->is_suspended = 0;
+	}
+
+	return 0;
+}
+
+static int __devinit omap_usb2_probe(struct platform_device *pdev)
+{
+	struct omap_usb			*phy;
+	struct usb_otg			*otg;
+	struct resource			*res;
+
+	phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy) {
+		dev_err(&pdev->dev, "unable to allocate memory for USB2 PHY\n");
+		return -ENOMEM;
+	}
+
+	otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL);
+	if (!otg) {
+		dev_err(&pdev->dev, "unable to allocate memory for USB OTG\n");
+		return -ENOMEM;
+	}
+
+	phy->dev		= &pdev->dev;
+
+	phy->phy.dev		= phy->dev;
+	phy->phy.label		= "omap-usb2";
+	phy->phy.set_suspend	= omap_usb2_suspend;
+	phy->phy.otg		= otg;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+
+	phy->control_dev = devm_request_and_ioremap(&pdev->dev, res);
+	if (phy->control_dev == NULL) {
+		dev_err(&pdev->dev, "Failed to obtain io memory\n");
+		return -ENXIO;
+	}
+
+	phy->is_suspended	= 1;
+	omap_usb_phy_power(phy, 0);
+
+	otg->set_host		= omap_usb_set_host;
+	otg->set_peripheral	= omap_usb_set_peripheral;
+	otg->set_vbus		= omap_usb_set_vbus;
+	otg->start_srp		= omap_usb_start_srp;
+	otg->phy		= &phy->phy;
+
+	phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
+	if (IS_ERR(phy->wkupclk)) {
+		dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
+		return PTR_ERR(phy->wkupclk);
+	}
+	clk_prepare(phy->wkupclk);
+
+	usb_add_phy(&phy->phy, USB_PHY_TYPE_USB2);
+
+	platform_set_drvdata(pdev, phy);
+
+	pm_runtime_enable(phy->dev);
+
+	return 0;
+}
+
+static int __devexit omap_usb2_remove(struct platform_device *pdev)
+{
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	clk_unprepare(phy->wkupclk);
+	usb_remove_phy(&phy->phy);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_RUNTIME
+
+static int omap_usb2_runtime_suspend(struct device *dev)
+{
+	struct platform_device	*pdev = to_platform_device(dev);
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	clk_disable(phy->wkupclk);
+
+	return 0;
+}
+
+static int omap_usb2_runtime_resume(struct device *dev)
+{
+	u32 ret = 0;
+	struct platform_device	*pdev = to_platform_device(dev);
+	struct omap_usb	*phy = platform_get_drvdata(pdev);
+
+	ret = clk_enable(phy->wkupclk);
+	if (ret < 0)
+		dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
+
+	return ret;
+}
+
+static const struct dev_pm_ops omap_usb2_pm_ops = {
+	SET_RUNTIME_PM_OPS(omap_usb2_runtime_suspend, omap_usb2_runtime_resume,
+		NULL)
+};
+
+#define DEV_PM_OPS     (&omap_usb2_pm_ops)
+#else
+#define DEV_PM_OPS     NULL
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_usb2_id_table[] = {
+	{ .compatible = "ti,omap-usb2" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
+#endif
+
+static struct platform_driver omap_usb2_driver = {
+	.probe		= omap_usb2_probe,
+	.remove		= __devexit_p(omap_usb2_remove),
+	.driver		= {
+		.name	= "omap-usb2",
+		.owner	= THIS_MODULE,
+		.pm	= DEV_PM_OPS,
+		.of_match_table = of_match_ptr(omap_usb2_id_table),
+	},
+};
+
+module_platform_driver(omap_usb2_driver);
+
+MODULE_ALIAS("platform: omap_usb2");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP USB2 phy driver");
+MODULE_LICENSE("GPL v2");

@@ -0,0 +1,46 @@
+/*
+ * omap_usb.h -- omap usb2 phy header file
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __DRIVERS_OMAP_USB2_H
+#define __DRIVERS_OMAP_USB2_H
+
+#include <linux/usb/otg.h>
+
+struct omap_usb {
+	struct usb_phy		phy;
+	struct phy_companion	*comparator;
+	struct device		*dev;
+	u32 __iomem		*control_dev;
+	struct clk		*wkupclk;
+	u8			is_suspended:1;
+};
+
+#define	PHY_PD	0x1
+
+#define	phy_to_omapusb(x)	container_of((x), struct omap_usb, phy)
+
+#if defined(CONFIG_OMAP_USB2) || defined(CONFIG_OMAP_USB2_MODULE)
+extern int omap_usb2_set_comparator(struct phy_companion *comparator);
+#else
+static inline int omap_usb2_set_comparator(struct phy_companion *comparator)
+{
+	return -ENODEV;
+}
+#endif
+
+#endif /* __DRIVERS_OMAP_USB_H */

@@ -0,0 +1,34 @@
+/*
+ * phy-companion.h -- phy companion to indicate the comparator part of PHY
+ *
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __DRIVERS_PHY_COMPANION_H
+#define __DRIVERS_PHY_COMPANION_H
+
+#include <linux/usb/otg.h>
+
+/* phy_companion to take care of VBUS, ID and srp capabilities */
+struct phy_companion {
+
+	/* effective for A-peripheral, ignored for B devices */
+	int	(*set_vbus)(struct phy_companion *x, bool enabled);
+
+	/* for B devices only:  start session with A-Host */
+	int	(*start_srp)(struct phy_companion *x);
+};
+
+#endif /* __DRIVERS_PHY_COMPANION_H */

@@ -19,3 +19,22 @@ Board specific device node entry
 &twl6030-usb {
 	usb-supply = <&vusb>;
 };
+
+TWL4030 USB PHY AND COMPARATOR
+ - compatible : Should be "ti,twl4030-usb"
+ - interrupts : The interrupt numbers to the cpu should be specified. First
+   interrupt number is the otg interrupt number that raises ID interrupts
+   and VBUS interrupts. The second interrupt number is optional.
+ - <supply-name>-supply : phandle to the regulator device tree node.
+   <supply-name> should be vusb1v5, vusb1v8 and vusb3v1
+ - usb_mode : The mode used by the phy to connect to the controller. "1"
+   specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode.
+
+twl4030-usb {
+	compatible = "ti,twl4030-usb";
+	interrupts = < 10 4 >;
+	usb1v5-supply = <&vusb1v5>;
+	usb1v8-supply = <&vusb1v8>;
+	usb3v1-supply = <&vusb3v1>;
+	usb_mode = <1>;
+};

@@ -585,23 +585,28 @@ static int __devinit twl4030_usb_probe(struct platform_device *pdev)
 	struct twl4030_usb	*twl;
 	int			status, err;
 	struct usb_otg		*otg;
-
-	if (!pdata) {
-		dev_dbg(&pdev->dev, "platform_data not available\n");
-		return -EINVAL;
-	}
+	struct device_node	*np = pdev->dev.of_node;
 
 	twl = devm_kzalloc(&pdev->dev, sizeof *twl, GFP_KERNEL);
 	if (!twl)
 		return -ENOMEM;
 
+	if (np)
+		of_property_read_u32(np, "usb_mode",
+				(enum twl4030_usb_mode *)&twl->usb_mode);
+	else if (pdata)
+		twl->usb_mode = pdata->usb_mode;
+	else {
+		dev_err(&pdev->dev, "twl4030 initialized without pdata\n");
+		return -EINVAL;
+	}
+
 	otg = devm_kzalloc(&pdev->dev, sizeof *otg, GFP_KERNEL);
 	if (!otg)
 		return -ENOMEM;
 
 	twl->dev		= &pdev->dev;
 	twl->irq		= platform_get_irq(pdev, 0);
-	twl->usb_mode		= pdata->usb_mode;
 	twl->vbus_supplied	= false;
 	twl->asleep		= 1;
 	twl->linkstat		= OMAP_MUSB_UNKNOWN;

@@ -690,12 +695,21 @@ static int __exit twl4030_usb_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static const struct of_device_id twl4030_usb_id_table[] = {
+	{ .compatible = "ti,twl4030-usb" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, twl4030_usb_id_table);
+#endif
+
 static struct platform_driver twl4030_usb_driver = {
 	.probe		= twl4030_usb_probe,
 	.remove		= __exit_p(twl4030_usb_remove),
 	.driver		= {
 		.name	= "twl4030_usb",
 		.owner	= THIS_MODULE,
+		.of_match_table = of_match_ptr(twl4030_usb_id_table),
 	},
 };
 

@@ -44,6 +44,7 @@ struct omap2430_glue {
 	struct platform_device	*musb;
 	enum omap_musb_vbus_id_status status;
 	struct work_struct	omap_musb_mailbox_work;
+	u32 __iomem		*control_otghs;
 };
 #define glue_to_musb(g)		platform_get_drvdata(g->musb)
 

@@ -51,6 +52,26 @@ struct omap2430_glue		*_glue;
 
 static struct timer_list musb_idle_timer;
 
+/**
+ * omap4_usb_phy_mailbox - write to usb otg mailbox
+ * @glue: struct omap2430_glue *
+ * @val: the value to be written to the mailbox
+ *
+ * On detection of a device (ID pin is grounded), this API should be called
+ * to set AVALID, VBUSVALID and ID pin is grounded.
+ *
+ * When OMAP is connected to a host (OMAP in device mode), this API
+ * is called to set AVALID, VBUSVALID and ID pin in high impedance.
+ *
+ * XXX: This function will be removed once we have a seperate driver for
+ * control module
+ */
+static void omap4_usb_phy_mailbox(struct omap2430_glue *glue, u32 val)
+{
+	if (glue->control_otghs)
+		writel(val, glue->control_otghs);
+}
+
 static void musb_do_idle(unsigned long _musb)
 {
 	struct musb	*musb = (void *)_musb;

@@ -245,6 +266,7 @@ EXPORT_SYMBOL_GPL(omap_musb_mailbox);
 
 static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 {
+	u32 val;
 	struct musb *musb = glue_to_musb(glue);
 	struct device *dev = musb->controller;
 	struct musb_hdrc_platform_data *pdata = dev->platform_data;

@@ -260,7 +282,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 		musb->xceiv->last_event = USB_EVENT_ID;
 		if (!is_otg_enabled(musb) || musb->gadget_driver) {
 			pm_runtime_get_sync(dev);
-			usb_phy_init(musb->xceiv);
+			val = AVALID | VBUSVALID;
+			omap4_usb_phy_mailbox(glue, val);
 			omap2430_musb_set_vbus(musb, 1);
 		}
 		break;

@@ -273,7 +296,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 		musb->xceiv->last_event = USB_EVENT_VBUS;
 		if (musb->gadget_driver)
 			pm_runtime_get_sync(dev);
-		usb_phy_init(musb->xceiv);
+		val = IDDIG | AVALID | VBUSVALID;
+		omap4_usb_phy_mailbox(glue, val);
 		break;
 
 	case OMAP_MUSB_ID_FLOAT:

@@ -291,7 +315,8 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 			if (musb->xceiv->otg->set_vbus)
 				otg_set_vbus(musb->xceiv->otg, 0);
 		}
-		usb_phy_shutdown(musb->xceiv);
+		val = SESSEND | IDDIG;
+		omap4_usb_phy_mailbox(glue, val);
 		break;
 	default:
 		dev_dbg(dev, "ID float\n");

@@ -366,6 +391,7 @@ err1:
 static void omap2430_musb_enable(struct musb *musb)
 {
 	u8		devctl;
+	u32		val;
 	unsigned long timeout = jiffies + msecs_to_jiffies(1000);
 	struct device *dev = musb->controller;
 	struct omap2430_glue *glue = dev_get_drvdata(dev->parent);

@@ -375,7 +401,8 @@ static void omap2430_musb_enable(struct musb *musb)
 	switch (glue->status) {
 
 	case OMAP_MUSB_ID_GROUND:
-		usb_phy_init(musb->xceiv);
+		val = AVALID | VBUSVALID;
+		omap4_usb_phy_mailbox(glue, val);
 		if (data->interface_type != MUSB_INTERFACE_UTMI)
 			break;
 		devctl = musb_readb(musb->mregs, MUSB_DEVCTL);

@@ -394,7 +421,8 @@ static void omap2430_musb_enable(struct musb *musb)
 		break;
 
 	case OMAP_MUSB_VBUS_VALID:
-		usb_phy_init(musb->xceiv);
+		val = IDDIG | AVALID | VBUSVALID;
+		omap4_usb_phy_mailbox(glue, val);
 		break;
 
 	default:

@@ -404,11 +432,14 @@ static void omap2430_musb_enable(struct musb *musb)
 
 static void omap2430_musb_disable(struct musb *musb)
 {
+	u32 val;
 	struct device *dev = musb->controller;
 	struct omap2430_glue *glue = dev_get_drvdata(dev->parent);
 
-	if (glue->status != OMAP_MUSB_UNKNOWN)
-		usb_phy_shutdown(musb->xceiv);
+	if (glue->status != OMAP_MUSB_UNKNOWN) {
+		val = SESSEND | IDDIG;
+		omap4_usb_phy_mailbox(glue, val);
+	}
 }
 
 static int omap2430_musb_exit(struct musb *musb)