[PATCH 1/5] ARM: dts: imx28.dtsi: Add auart support

@@ -22,6 +22,11 @@
 		gpio4 = &gpio4;
 		saif0 = &saif0;
 		saif1 = &saif1;
+		serial0 = &auart0;
+		serial1 = &auart1;
+		serial2 = &auart2;
+		serial3 = &auart3;
+		serial4 = &auart4;
 	};
 
 	cpus {

@@ -167,6 +172,22 @@
 					fsl,pull-up = <0>;
 				};
 
+				auart0_pins_a: auart0 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x3000 0x3010 0x3020 0x3030>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				auart3_pins_a: auart3 at 0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x30c0 0x30d0 0x30e0 0x30f0>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				mac0_pins_a: mac0 at 0 {
 					reg = <0>;
 					fsl,pinmux-ids = <0x4000 0x4010 0x4020

@@ -404,30 +425,35 @@
 			};
 
 			auart0: serial@8006a000 {
+				compatible = "fsl,mxs-auart";
 				reg = <0x8006a000 0x2000>;
 				interrupts = <112 70 71>;
 				status = "disabled";
 			};
 
 			auart1: serial at 8006c000 {
+				compatible = "fsl,mxs-auart";
 				reg = <0x8006c000 0x2000>;
 				interrupts = <113 72 73>;
 				status = "disabled";
 			};
 
 			auart2: serial at 8006e000 {
+				compatible = "fsl,mxs-auart";
 				reg = <0x8006e000 0x2000>;
 				interrupts = <114 74 75>;
 				status = "disabled";
 			};
 
 			auart3: serial at 80070000 {
+				compatible = "fsl,mxs-auart";
 				reg = <0x80070000 0x2000>;
 				interrupts = <115 76 77>;
 				status = "disabled";
 			};
 
 			auart4: serial at 80072000 {
+				compatible = "fsl,mxs-auart";
 				reg = <0x80072000 0x2000>;
 				interrupts = <116 78 79>;
 				status = "disabled";

@@ -73,6 +73,18 @@
 				pinctrl-0 = <&duart_pins_a>;
 				status = "okay";
 			};
+
+			auart0: serial at 8006a000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&auart0_pins_a>;
+		        	status = "okay";
+			};
+
+			auart3: serial at 80070000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&auart3_pins_a>;
+		        	status = "okay";
+			};
 		};
 	};
 

@@ -33,6 +33,7 @@
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/pinctrl/consumer.h>
+#include <linux/of_device.h>
 
 #include <asm/cacheflush.h>
 

@@ -675,6 +676,44 @@ static struct uart_driver auart_driver = {
 #endif
 };
 
+#ifdef CONFIG_OF
+/*
+ * This function returns 1 if pdev isn't a device instatiated by dt, 0 if it
+ * could successfully get all information from dt or a negative errno.
+ */
+static int serial_mxs_probe_dt(struct mxs_auart_port *s,
+		struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int ret;
+
+	if (!np)
+		/* no device tree device */
+		return 1;
+
+	ret = of_alias_get_id(np, "serial");
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to get alias id: %d\n", ret);
+		return ret;
+	}
+	s->port.line = ret;
+
+	return 0;
+}
+#else
+static inline int serial_mxs_probe_dt(struct mxs_auart_port *s,
+		struct platform_device *pdev)
+{
+	return 1;
+}
+#endif
+
+static void mxs_auart_probe_pdev(struct mxs_auart_port *s,
+		struct platform_device *pdev)
+{
+	s->port.line = pdev->id < 0 ? 0 : pdev->id;
+}
+
 static int __devinit mxs_auart_probe(struct platform_device *pdev)
 {
 	struct mxs_auart_port *s;

@@ -689,6 +728,14 @@ static int __devinit mxs_auart_probe(struct platform_device *pdev)
 		goto out;
 	}
 
+	ret = serial_mxs_probe_dt(s, pdev);
+	if (ret > 0)
+		mxs_auart_probe_pdev(s, pdev);
+	else if (ret < 0) {
+		ret = -EINVAL;
+		goto out_free;
+	}
+
 	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	if (IS_ERR(pinctrl)) {
 		ret = PTR_ERR(pinctrl);

@@ -711,7 +758,6 @@ static int __devinit mxs_auart_probe(struct platform_device *pdev)
 	s->port.membase = ioremap(r->start, resource_size(r));
 	s->port.ops = &mxs_auart_ops;
 	s->port.iotype = UPIO_MEM;
-	s->port.line = pdev->id < 0 ? 0 : pdev->id;
 	s->port.fifosize = 16;
 	s->port.uartclk = clk_get_rate(s->clk);
 	s->port.type = PORT_IMX;

@@ -769,12 +815,19 @@ static int __devexit mxs_auart_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static struct of_device_id mxs_auart_dt_ids[] = {
+	{.compatible = "fsl,mxs-auart", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_auart_dt_ids);
+
 static struct platform_driver mxs_auart_driver = {
 	.probe = mxs_auart_probe,
 	.remove = __devexit_p(mxs_auart_remove),
 	.driver = {
 		.name = "mxs-auart",
 		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(mxs_auart_dt_ids),
 	},
 };
 

@@ -77,6 +77,7 @@ CONFIG_DEVPTS_MULTIPLE_INSTANCES=y
 # CONFIG_DEVKMEM is not set
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_SERIAL_MXS_AUART=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 # CONFIG_I2C_COMPAT is not set

@@ -0,0 +1,14 @@
+* Freescale MXS Application UART (AUART)
+
+Required properties:
+- compatible : Should be "fsl,mxs-uart"
+- reg : Address and length of the register set for the device
+- interrupts : Should contain the auart interrupt
+
+Example:
+auart0: serial at 8006a000 {
+	compatible = "fsl,mxs-auart";
+	reg = <0x8006a000 0x2000>;
+	interrupts = <112 70 71>;
+};
+