@@ -313,16 +313,6 @@ config SPI_S3C24XX_FIQ
no free DMA channels, or when doing transfers that required both
TX and RX data paths.
-config SPI_S3C24XX_GPIO
- tristate "Samsung S3C24XX series SPI by GPIO"
- depends on ARCH_S3C2410 && EXPERIMENTAL
- select SPI_BITBANG
- help
- SPI driver for Samsung S3C24XX series ARM SoCs using
- GPIO lines to provide the SPI bus. This can be used where
- the inbuilt hardware cannot provide the transfer mode, or
- where the board is using non hardware connected pins.
-
config SPI_S3C64XX
tristate "Samsung S3C64XX series type SPI"
depends on (ARCH_S3C64XX || ARCH_S5P64X0)
@@ -1,200 +0,0 @@
-/*
- * Copyright (c) 2006 Ben Dooks
- * Copyright (c) 2006 Simtec Electronics
- *
- * S3C24XX GPIO based SPI driver
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
-*/
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/workqueue.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/spi_bitbang.h>
-
-#include <mach/regs-gpio.h>
-#include <mach/spi-gpio.h>
-#include <mach/hardware.h>
-
-struct s3c2410_spigpio {
- struct spi_bitbang bitbang;
-
- struct s3c2410_spigpio_info *info;
- struct platform_device *dev;
-};
-
-static inline struct s3c2410_spigpio *spidev_to_sg(struct spi_device *spi)
-{
- return spi_master_get_devdata(spi->master);
-}
-
-static inline void setsck(struct spi_device *dev, int on)
-{
- struct s3c2410_spigpio *sg = spidev_to_sg(dev);
- s3c2410_gpio_setpin(sg->info->pin_clk, on ? 1 : 0);
-}
-
-static inline void setmosi(struct spi_device *dev, int on)
-{
- struct s3c2410_spigpio *sg = spidev_to_sg(dev);
- s3c2410_gpio_setpin(sg->info->pin_mosi, on ? 1 : 0);
-}
-
-static inline u32 getmiso(struct spi_device *dev)
-{
- struct s3c2410_spigpio *sg = spidev_to_sg(dev);
- return s3c2410_gpio_getpin(sg->info->pin_miso) ? 1 : 0;
-}
-
-#define spidelay(x) ndelay(x)
-
-#include "spi-bitbang-txrx.h"
-
-
-static u32 s3c2410_spigpio_txrx_mode0(struct spi_device *spi,
- unsigned nsecs, u32 word, u8 bits)
-{
- return bitbang_txrx_be_cpha0(spi, nsecs, 0, 0, word, bits);
-}
-
-static u32 s3c2410_spigpio_txrx_mode1(struct spi_device *spi,
- unsigned nsecs, u32 word, u8 bits)
-{
- return bitbang_txrx_be_cpha1(spi, nsecs, 0, 0, word, bits);
-}
-
-static u32 s3c2410_spigpio_txrx_mode2(struct spi_device *spi,
- unsigned nsecs, u32 word, u8 bits)
-{
- return bitbang_txrx_be_cpha0(spi, nsecs, 1, 0, word, bits);
-}
-
-static u32 s3c2410_spigpio_txrx_mode3(struct spi_device *spi,
- unsigned nsecs, u32 word, u8 bits)
-{
- return bitbang_txrx_be_cpha1(spi, nsecs, 1, 0, word, bits);
-}
-
-
-static void s3c2410_spigpio_chipselect(struct spi_device *dev, int value)
-{
- struct s3c2410_spigpio *sg = spidev_to_sg(dev);
-
- if (sg->info && sg->info->chip_select)
- (sg->info->chip_select)(sg->info, value);
-}
-
-static int s3c2410_spigpio_probe(struct platform_device *dev)
-{
- struct s3c2410_spigpio_info *info;
- struct spi_master *master;
- struct s3c2410_spigpio *sp;
- int ret;
-
- master = spi_alloc_master(&dev->dev, sizeof(struct s3c2410_spigpio));
- if (master == NULL) {
- dev_err(&dev->dev, "failed to allocate spi master\n");
- ret = -ENOMEM;
- goto err;
- }
-
- sp = spi_master_get_devdata(master);
-
- platform_set_drvdata(dev, sp);
-
- /* copy in the plkatform data */
- info = sp->info = dev->dev.platform_data;
-
- /* setup spi bitbang adaptor */
- sp->bitbang.master = spi_master_get(master);
- sp->bitbang.master->bus_num = info->bus_num;
- sp->bitbang.master->num_chipselect = info->num_chipselect;
- sp->bitbang.chipselect = s3c2410_spigpio_chipselect;
-
- sp->bitbang.txrx_word[SPI_MODE_0] = s3c2410_spigpio_txrx_mode0;
- sp->bitbang.txrx_word[SPI_MODE_1] = s3c2410_spigpio_txrx_mode1;
- sp->bitbang.txrx_word[SPI_MODE_2] = s3c2410_spigpio_txrx_mode2;
- sp->bitbang.txrx_word[SPI_MODE_3] = s3c2410_spigpio_txrx_mode3;
-
- /* set state of spi pins, always assume that the clock is
- * available, but do check the MOSI and MISO. */
- s3c2410_gpio_setpin(info->pin_clk, 0);
- s3c2410_gpio_cfgpin(info->pin_clk, S3C2410_GPIO_OUTPUT);
-
- if (info->pin_mosi < S3C2410_GPH10) {
- s3c2410_gpio_setpin(info->pin_mosi, 0);
- s3c2410_gpio_cfgpin(info->pin_mosi, S3C2410_GPIO_OUTPUT);
- }
-
- if (info->pin_miso != S3C2410_GPA0 && info->pin_miso < S3C2410_GPH10)
- s3c2410_gpio_cfgpin(info->pin_miso, S3C2410_GPIO_INPUT);
-
- ret = spi_bitbang_start(&sp->bitbang);
- if (ret)
- goto err_no_bitbang;
-
- return 0;
-
- err_no_bitbang:
- spi_master_put(sp->bitbang.master);
- err:
- return ret;
-
-}
-
-static int s3c2410_spigpio_remove(struct platform_device *dev)
-{
- struct s3c2410_spigpio *sp = platform_get_drvdata(dev);
-
- spi_bitbang_stop(&sp->bitbang);
- spi_master_put(sp->bitbang.master);
-
- return 0;
-}
-
-/* all gpio should be held over suspend/resume, so we should
- * not need to deal with this
-*/
-
-#define s3c2410_spigpio_suspend NULL
-#define s3c2410_spigpio_resume NULL
-
-/* work with hotplug and coldplug */
-MODULE_ALIAS("platform:spi_s3c24xx_gpio");
-
-static struct platform_driver s3c2410_spigpio_drv = {
- .probe = s3c2410_spigpio_probe,
- .remove = s3c2410_spigpio_remove,
- .suspend = s3c2410_spigpio_suspend,
- .resume = s3c2410_spigpio_resume,
- .driver = {
- .name = "spi_s3c24xx_gpio",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init s3c2410_spigpio_init(void)
-{
- return platform_driver_register(&s3c2410_spigpio_drv);
-}
-
-static void __exit s3c2410_spigpio_exit(void)
-{
- platform_driver_unregister(&s3c2410_spigpio_drv);
-}
-
-module_init(s3c2410_spigpio_init);
-module_exit(s3c2410_spigpio_exit);
-
-MODULE_DESCRIPTION("S3C24XX SPI Driver");
-MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>");
-MODULE_LICENSE("GPL");