[PATCH v6.1 3/3] omap3: beaglexm: fix power on of DVI
From: nm@ti.com (Nishanth Menon)
Date: 2011-01-12 00:23:29
From: Koen Kooi <redacted> TFP410 DVI chip is used to provide display out. This chip is controlled by 2 lines: LDO which supplies the power is controlled over gpio + 2 and the enable of the chip itself is done over gpio + 1 NOTE: the LDO is necessary for LED, serial blocks as well. gpio + 1 was used to sense USB overcurrent in vanilla beagle. Without this fix, the display would not function as the LDO remains shut down. [nm at ti.com: split up, added descriptive changelogs] Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Koen Kooi <redacted> --- Posting the last of the patches of this series v6.1: formal submission: added gpio error checks v5: http://marc.info/?t=129476616900006&r=1&w=2 arch/arm/mach-omap2/board-omap3beagle.c | 42 ++++++++++++++++++++++++++++-- 1 files changed, 39 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 673deb9..2ed8040 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c@@ -273,6 +273,8 @@ static struct gpio_led gpio_leds[]; static int beagle_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { + int r; + if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { mmc[0].gpio_wp = -EINVAL; } else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
@@ -293,9 +295,16 @@ static int beagle_twl_gpio_setup(struct device *dev, /* REVISIT: need ehci-omap hooks for external VBUS * power switch and overcurrent detect */ - - gpio_request(gpio + 1, "EHCI_nOC"); - gpio_direction_input(gpio + 1); + if (omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) { + r = gpio_request(gpio + 1, "EHCI_nOC"); + if (!r) { + r = gpio_direction_input(gpio + 1); + if (r) + gpio_free(gpio + 1); + } + if (r) + pr_err("%s: unable to configure EHCI_nOC\n", __func__); + } /* * TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
@@ -316,6 +325,33 @@ static int beagle_twl_gpio_setup(struct device *dev, /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1; + /* + * gpio + 1 on Xm controls the TFP410's enable line (active low) + * gpio + 2 control varies depending on the board rev as follows: + * P7/P8 revisions(prototype): Camera EN + * A2+ revisions (production): LDO (supplies DVI, serial, led blocks) + */ + if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) { + r = gpio_request(gpio + 1, "nDVI_PWR_EN"); + if (!r) { + r = gpio_direction_output(gpio + 1, 0); + if (r) + gpio_free(gpio + 1); + } + if (r) + pr_err("%s: unable to configure nDVI_PWR_EN\n", + __func__); + r = gpio_request(gpio + 2, "DVI_LDO_EN"); + if (!r) { + r = gpio_direction_output(gpio + 2, 1); + if (r) + gpio_free(gpio + 2); + } + if (r) + pr_err("%s: unable to configure DVI_LDO_EN\n", + __func__); + } + return 0; }
--
1.6.3.3