[PATCHv3 0/2] omap3: Devkit8000: misc fixes

Here is a set of misc fixes for the devkit8000.

The only really notable one is the lcd enable gpio fix. It gets rid
of some nasty low level twl4030 calls and replaces them with generic gpio
calls. It also fixes a bug where the screen would not turn off when
blanking.

Changes from v1: 
	Pull the indention fix into "Change lcd power pin".
	Change the pin for lcd pwren.
	Fix the pullup/pulldown configuration after lcd prwen correction.

Changes from v2:
	Better comment for removing low level functions used for twl4030 gpio
	Fix indention => indentation in comment

Daniel Morsing (1):
  OMAP3: Devkit8000: Fix tps65930 pullup/pulldown configuration

Thomas Weber (1):
  OMAP3: Devkit8000: Change lcd power pin

 arch/arm/mach-omap2/board-devkit8000.c |   10 +++-------
 1 files changed, 3 insertions(+), 7 deletions(-)

-- 
1.7.4.rc2

From: Daniel Morsing <redacted>

gpio7 on the tps65930 is used as an output on the devkit8000 and
gpio1 is not connected. Remove gpio7 and change gpio1 to pulldown

Signed-off-by: Daniel Morsing <redacted>
---
 arch/arm/mach-omap2/board-devkit8000.c |    3 +--
 1 files changed, 1 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 719f4e5..9fb416b 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c

@@ -262,8 +262,7 @@ static struct twl4030_gpio_platform_data devkit8000_gpio_data = {
 	.irq_base	= TWL4030_GPIO_IRQ_BASE,
 	.irq_end	= TWL4030_GPIO_IRQ_END,
 	.use_leds	= true,
-	.pullups	= BIT(1),
-	.pulldowns	= BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
+	.pulldowns	= BIT(1) | BIT(2) | BIT(6) | BIT(8) | BIT(13)
 				| BIT(15) | BIT(16) | BIT(17),
 	.setup		= devkit8000_twl_gpio_setup,
 };

-- 
1.7.4.rc2

This patch fixes a wrongly used lcd enable pin.

The Devkit8000 uses twl4030_ledA configured as output gpio only for the
lcd enable line. twl4030_gpio.1 is used through the generic gpio functions
while ledA is used via low level twl4030 calls.

Remove the low level calls and use the generic gpio functions for
initialization and use of ledA.

This also fixes a bug where the lcd would not power down when blanking.

Fix indentation issue. The comment line uses 8 whitespace.
This is replaced with one tabulator.

Reported-by: Daniel Morsing <redacted>
Signed-off-by: Thomas Weber <redacted>
---
 arch/arm/mach-omap2/board-devkit8000.c |    7 ++-----
 1 files changed, 2 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c
index 451e7ff..719f4e5 100644
--- a/arch/arm/mach-omap2/board-devkit8000.c
+++ b/arch/arm/mach-omap2/board-devkit8000.c

@@ -114,9 +114,6 @@ static struct omap2_hsmmc_info mmc[] = {
 
 static int devkit8000_panel_enable_lcd(struct omap_dss_device *dssdev)
 {
-	twl_i2c_write_u8(TWL4030_MODULE_GPIO, 0x80, REG_GPIODATADIR1);
-	twl_i2c_write_u8(TWL4030_MODULE_LED, 0x0, 0x0);
-
 	if (gpio_is_valid(dssdev->reset_gpio))
 		gpio_set_value_cansleep(dssdev->reset_gpio, 1);
 	return 0;

@@ -245,8 +242,8 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
 	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
 	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
 
-        /* gpio + 1 is "LCD_PWREN" (out, active high) */
-	devkit8000_lcd_device.reset_gpio = gpio + 1;
+	/* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
+	devkit8000_lcd_device.reset_gpio = gpio + TWL4030_GPIO_MAX + 0;
 	gpio_request(devkit8000_lcd_device.reset_gpio, "LCD_PWREN");
 	/* Disable until needed */
 	gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0);

-- 
1.7.4.rc2

On Tue, Jan 18, 2011 at 12:28, Thomas Weber [off-list ref] wrote:

Consider checking the return value of gpio_request().

? ? ? ?/* Disable until needed */
? ? ? ?gpio_direction_output(devkit8000_lcd_device.reset_gpio, 0);
--
1.7.4.rc2