[PATCH] Removing dead OMAP_IR
From: Christoph Egger <hidden>
Date: 2010-06-30 15:55:22
Subsystem:
arm port, omap1 support, omap2+ support, the rest · Maintainers:
Russell King, Aaro Koskinen, Janusz Krzysztofik, Andreas Kemnade, Kevin Hilman, Roger Quadros, Tony Lindgren, Linus Torvalds
OMAP_IR doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <redacted> [tony at atomide.com: updated for new mux code] Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index ee46974..2efa427 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c@@ -292,15 +292,6 @@ static struct platform_device h2_kp_device = { #define H2_IRDA_FIRSEL_GPIO_PIN 17 -#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE) -static int h2_transceiver_mode(struct device *dev, int state) -{ - /* SIR when low, else MIR/FIR when HIGH */ - gpio_set_value(H2_IRDA_FIRSEL_GPIO_PIN, !(state & IR_SIRMODE)); - return 0; -} -#endif - static struct omap_irda_config h2_irda_data = { .transceiver_cap = IR_SIRMODE | IR_MIRMODE | IR_FIRMODE, .rx_channel = OMAP_DMA_UART3_RX,
@@ -450,15 +441,6 @@ static void __init h2_init(void) omap_cfg_reg(E19_1610_KBR4); omap_cfg_reg(N19_1610_KBR5); - /* Irda */ -#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE) - omap_writel(omap_readl(FUNC_MUX_CTRL_A) | 7, FUNC_MUX_CTRL_A); - if (gpio_request(H2_IRDA_FIRSEL_GPIO_PIN, "IRDA mode") < 0) - BUG(); - gpio_direction_output(H2_IRDA_FIRSEL_GPIO_PIN, 0); - h2_irda_data.transceiver_mode = h2_transceiver_mode; -#endif - platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices)); omap_board_config = h2_config; omap_board_config_size = ARRAY_SIZE(h2_config);
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index 2d9ff0f..9044dcf 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c@@ -356,10 +356,6 @@ static void __init omap_h4_init(void) * You have to mux them off in device drivers later on * if not needed. */ -#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE) - omap_mux_init_signal("uart3_tx_irtx.uart3_tx_irtx", 0); - omap_mux_init_signal("uart3_rx_irrx.uart3_rx_irrx", 0); -#endif #if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE) omap_mux_init_gpio(88, OMAP_PULL_ENA | OMAP_PULL_UP); --6TrnltStXW4iwmi0--